You should understand the issues and know how to fix the chainsaw as it helps you save money and time, and still have the saw running. Here, we shall discuss some of the problems that prevent a chainsaw from working and the best solutions as to why your chainsaw won’t stay running. If the chainsaw is on a flat surface, put your right foot on the handle while your left-hand holds the top of your chainsaw.
Try to relax and read our guide to possibly find the reason why your chainsaw won’t stay running. If the idle port of your chainsaw gets blocked or damaged, your chainsaw won’t stay running. If you have more chainsaw questions, here at Canberra Diamond Blade, we are happy to help! In the meantime, check out our other chainsaw articles answering questions like if it’s worth sharpening a chainsaw chain.
The primary reason that is why your chainsaw won’t stay running is the faulty carb. In your chainsaw, there is an idle port which is responsible to keep your chainsaw in idle position. Thus, the port will apply force to make your chainsaw stay running.
As unfortunate as it may be, this is a problem that everyone with a chainsaw will run into at one time or another: your chainsaw will fire, but will not idle or stay running. If your chainsaw has been sitting for a while, the gas in it may have either evaporated or gone bad, both of which will prevent your chainsaw from running correctly. The air intake system in chainsaws is relatively simple and is not likely to be the cause of many problems, if any, at all, but there is one piece that is worth checking if you can’t get your chainsaw to stay running.
why won’t my chainsaw stay running Related Question:
Why does my chainsaw start but wont stay running?
A clogged fuel filter will starve your chainsaw’s engine, and it can also damage it by letting contaminated fuel into the engine. Bad fuel can also clog the carburettor. Clogged carburettors are one of the most common reasons why a chainsaw won’t stay running or start at all.
Why does my chainsaw stop running after a few minutes?
A clogged carburetor is often caused by leaving fuel in the chainsaw for a long period of time. Over time, some of the ingredients in the fuel may evaporate, leaving behind a thicker, stickier substance. This sticky fuel can clog up the carburetor and cause the chainsaw engine to stall.
Why does my chainsaw stop when I give it gas?
If the filter becomes clogged, not enough fuel will reach the engine for it to run properly. Because your chainsaw will idle, but dies when it is revved up to full power, it means that the filter is only partially clogged; it will allow enough fuel to the engine to run on idle, but not enough to sustain full throttle.
Why does my chainsaw turn off after 15 minutes?
The most common problems why a chainsaw does not stay running are: Spark Switch/Plugs. Bad Fuel. Blocked Carburetor.
Why does my Stihl chainsaw dies when I give it gas?
An engine stalls when it’s getting too much or not enough fuel from the carburetor. Stihl chainsaw carburetors usually have three adjustment screws: one each for idle, low speed and high speed. If the saw stalls while it’s idling, adjusting the idle screw, which usually is marked LA, should help.
What causes a chainsaw to bog down when accelerating?
The reason for that may be you’re using the saw at altitude or the carburetor adjustment has simply slipped. The saw also won’t operate well at speed if the air filter or spark arrestor or carburetor are dirty.
Can you clean a chainsaw carburetor without taking it apart?
To clean a carb, you have to take it apart. If it needs cleaning, the parts that need cleaning can’t be seen from the outside.
How do you clean a carburetor without removing it?
To clean a motorcycle carburetor without removing it, you’ll need to remove the bowls at the bottom of the carburetor. Once the bowls are removed, spray some carburetor cleaner up inside, wait a few minutes, then spray again to ensure coverage. Then replace the bowls and start the motorcycle to assess how it runs.
Why does my chainsaw spark?
The most common cause of sparks from a chainsaw is metal-on-metal grinding. Whether it’s cutting through wood that has a nail in it or a grinding of gears in the chainsaw housing, a metal-against-metal grinding is the most likely cause.
Why does my chainsaw only runs on choke?
When your chainsaw only runs if the choke is on the problem, in most cases, is a result of fuel supply problems or a faulty carburetor. To fix the problem you should check and clean the fuel system and carburator.
What do the high and low screws do on a chainsaw?
Most Pro Saw Engines Have Three Carburetor Adjusting Screws: If this adjustment is set too low, the engine will die when the throttle trigger is released. If this adjustment is set too high, the high idle speed will cause the centrifugal clutch to engage and the chain will run.