The next iteration of chainsaw oiler was still manual, and because it involved an onboard thumb plunger next to the throttle, it eliminated the need for a “Chainsaw caddy.” This advancement in chainsaw oiling technology allowed the operator to manually pump oil onto the bar while cutting. If the chain spits small amounts of oil onto the wood, you’ll know that your chainsaw oiler is functioning properly. As always, if you’ve got any other pro-tips on how to keep your chainsaw oiler functioning properly, feel free to leave them in the comments section below!
Chainsaw oiler consists of an oil pump, oil lines, and oil holes. With the oiler system cleaned from all the debris and gunk, reassemble everything and start your Chainsaw. For electric chainsaw models, you should examine the oiler after each use and make sure it gets replenished when empty.
If your chainsaw is new or you have replaced your chain and guide bar, you will need to keep adjusting the oiler until you determine the right setting that will enable the oiler to produce just the right amount of lubrication. If the above fixes do not work or oiler problems keep recurring, this could indicate that your oiler may be damaged. To ensure that the oiler is functioning correctly, start the chainsaw and let it run for a few minutes then direct the tip of the chainsaw blade towards a piece of wood.
In this article I’m going to explain why it’s important to keep the chain lubricated and how chainsaw oilers work. With manual oilers you need to release oil onto the chain, usually by pressing a pump button. Some chainsaws come with automatic oilers which allow you to adjust the flow rate of the bar oil.
how does chainsaw bar oiler work Related Question:
How do you clean a chainsaw oiler?
Wipe oil and sawdust from the bar, including from the groove in the bar’s rim, by using a rag. Clean the oil feed hole on the bar by poking 16-gauge wire through it. Poke the wire into the oil outlet port on the body of the saw to remove sawdust and dirt that may block it.
Can I use 10w30 for chainsaw bar oil?
As a matter of fact, you can actually use regular 10w30 motor oil on a chainsaw as one of the alternatives in case you don’t have bar and chain oil. That’s because 10w30 oil has enough thickness and viscosity that will allow it to withstand the friction that is happening whenever you are using a chainsaw.
Can you use 10w40 in a chainsaw?
You can but it’s not very good for the chain or the environment. The Husqvarna / Stihl stuff is much thicker and vegetable based so it doesn’t fling off the chain as easily or poison your garden! 10w30. Thicker.
Is it normal for a chainsaw to leak bar oil?
In all but very exceptional cases there is nothing wrong with the chainsaw and what appears to be an oil leak is simply oil that has sprayed from the chain as it rotates at high speed, draining from the saw body and guide bar.
How do you remove oil from a bar?
Allow the alcohol a few minutes to break down the oil, then rub the area with a simple bar soap, like Ivory. Work the soap into the stain and rinse. Let the area air dry and make sure the stain is gone. If not, repeat the process.
What happens when the oil pump goes out?
A faulty oil pump will cause oil pressure to decrease to the point where oil can’t flow into the hydraulic lifters of the engine. This will cause the hydraulic lifters to make noise because they aren’t being properly lubricated. As a result, they will wear out quickly.
How long do oil pumps last?
You’ll want to check your owner’s manual or the manufacturer’s information online to see how long your particular oil pump should last. Keep in mind that it’s either time or the number of miles, whichever comes first. If you use 12,000 miles per year as a guide, a typical oil pump should last between 5 and 5.84 years.
How do I know if my oil sensor is bad?
The best way to test if your sensor is bad is through the lights on the oil pressure gauge. If the low oil pressure warning light comes on when they engine’s oil levels are normal and your engine is running smoothly and quietly, then you likely have a bad oil pressure sensor.
Can I use 2 stroke oil for chainsaw bar oil?
Can You Use 2 Cycle Oil As Bar Oil? You should only use two-cycle oil as the mix, never as a chainsaw bar oil alternative. Using two-cycle oil on the bar will not provide enough tackiness to stick to the chainsaw chain in the summer months. Two-cycle oil also will not work in the winter.
What weight is chainsaw bar oil?
What viscosity is chainsaw bar oil? The viscosity of chainsaw bar oil can vary depending on the formula but 30W is standard. In cold weather, a thin 10W chainsaw oil may be advantageous, while very hot temperatures may require a much thicker 40W or 50W formula.
What motor oil Can you use for chainsaw bar oil?
If your manufacturer’s bar and chain oil is unavailable, you can use SAE 30 weight motor oil to lube your chain during the summer and SAE 10 weight during the winter, according to the University of Missouri Extension.
How do I stop my chainsaw from leaking bar oil?
It’s important to note that oil tanks cannot simply vent into the atmosphere, as this could lead to the oil leaking onto the operator during use. To avoid your chainsaw from leaking oil whist in storage, the best solution is to drain the chainsaw of its bar oil and fuel mix and store the chainsaw empty.
How much oil should a chainsaw use?
When to Oil Gas chainsaws use about one tank of bar and chain oil for every tank of fuel, so fill the reservoir every time you fill the tank.
Can engine oil be used as chainsaw oil?
While motor oil is not the best substitute for chainsaw bar oil, it will work as a temporary measure if find you have no other option. The downside of motor oil is that it’s not sticky enough to stay on the bar and chain. So, when you’re using the chainsaw, the motor oil will fling off as you cut and make quite a mess.
Is bar oil the same as motor oil?
Bar and chain oil is stickier than regular motor oil, so it stays on the chain longer. Motor oil flings off the chain more quickly, so if you try Terry’s tip, be prepared to refill the oil on your chain saw more quickly than with regular bar and chain oil.