The next iteration of chainsaw oiler was still manual, and because it involved an onboard thumb plunger next to the throttle, it eliminated the need for a “Chainsaw caddy.” This advancement in chainsaw oiling technology allowed the operator to manually pump oil onto the bar while cutting. If the chain spits small amounts of oil onto the wood, you’ll know that your chainsaw oiler is functioning properly. As always, if you’ve got any other pro-tips on how to keep your chainsaw oiler functioning properly, feel free to leave them in the comments section below!
Chainsaw oiler consists of an oil pump, oil lines, and oil holes. With the oiler system cleaned from all the debris and gunk, reassemble everything and start your Chainsaw. For electric chainsaw models, you should examine the oiler after each use and make sure it gets replenished when empty.
The oil system on a Stihl chainsaw lubricates the engine and the bar and chain. The bar and chain oil on a Stihl chainsaw originates from the oil tank on the same side as the gas tank. Stihl chainsaws use an automatic oil pump, which means that whenever the engine reaches a high enough speed to engage the chain, the pump is also activated, taking the hassle out of manually trying to engage the oil pump and control the flow of oil to the bar.
In this article I’m going to explain why it’s important to keep the chain lubricated and how chainsaw oilers work. With manual oilers you need to release oil onto the chain, usually by pressing a pump button. Some chainsaws come with automatic oilers which allow you to adjust the flow rate of the bar oil.
how does chainsaw bar oil work Related Question:
How does Stihl chainsaw bar oil work?
For a chainsaw engine, the gasoline is mixed with a two-stroke air-cooled engine oil. When the gas reaches the cylinder and gets ignited, the oil-rich fuel will also lubricate the piston and the crankshaft, which allows the piston and the crankcase to receive the proper lubrication to keep moving at high speeds.
What happens if you don’t use bar oil in a chainsaw?
Without lubricant, the speed at which the chain moves over the chainsaw bar can cause some serious friction. A slowed-down chain and excessive fuel burning mean there’s a lot of friction between your bar and chain, which means a lot of heat is being produced that could do major damage to your saw.
How does an Oiler work?
An oiler is typically a junior position within the engineering department of a vessel. In addition to maintaining proper lubrication for the propulsion engine of a ship, the oiler keeps tabs on the lubrication of other shipboard equipment such as air conditioning, sewage systems and water pumps.
Why is my chainsaw using so much oil?
What causes a chainsaw to leak oil? As the oil is pumped from the tank through to the guide bar, air begins to replace the space where the oil was previously stored. If there isn’t proper ventilation of the oil tank, a vacuum can occur and reduce the flow of oil to the guide bar.
Can I use WD40 as chainsaw oil?
No. You should never use WD40 as chain lubricant since WD-40 is NOT a true lubricant. WD40 is primarily a solvent or rust dissolver.
What’s the difference between chainsaw bar oil and regular oil?
Bar and chain oil is stickier than regular motor oil, so it stays on the chain longer. Motor oil flings off the chain more quickly, so if you try Terry’s tip, be prepared to refill the oil on your chain saw more quickly than with regular bar and chain oil.
How does a chainsaw automatic oiler work?
The throttle simultaneously engages the motor and the oil pump. As you throttle up, a worm drive engages the pump to send oil through a port that releases onto the bar. As the chain moves across the bar, it distributes the oil across the surface, reducing the friction and the heat that occurs when cutting.
How do I know if my chainsaw oil pump is bad?
Generally speaking, the signs of a chainsaw oiler problem are easily spotted. If the chainsaw seems like it’s getting too hot or producing smoke, that is a sign that there is an oil deficiency in the chain. This is not good for the life of your chainsaw. If you spot this problem, it is time to troubleshoot the issue.
How do you clean a chainsaw Oiler?
Wipe oil and sawdust from the bar, including from the groove in the bar’s rim, by using a rag. Clean the oil feed hole on the bar by poking 16-gauge wire through it. Poke the wire into the oil outlet port on the body of the saw to remove sawdust and dirt that may block it.
How do you store a chainsaw so it doesn’t leak oil?
Store your larger chainsaws on the ground or a shelf, and hang the smaller ones on the wall to keep them from being lost. Before storing your chainsaws, always make sure that the oil reservoir is empty. If it’s not, ensure to drain the oil. Must secure the plugs after every use and before storage.
Do all chainsaws leak bar oil?
In all but very exceptional cases there is nothing wrong with the chainsaw and what appears to be an oil leak is simply oil that has sprayed from the chain as it rotates at high speed, draining from the saw body and guide bar.
Can you over oil a chainsaw?
Although a chain saw always requires the moisture that oil provides during the saw’s operation, too much oil isn’t good. When the oil adjustment is set too high, the oil is subject to drip from the chain and run down the guide bar.
How often do you oil a chainsaw?
The chain saw should be oiled before each cut. For Manual Oiling System: Lubricate the saw chain by pressing the bulb on the oil reservoir cap twice before making each cut. Hold the bulb down for 3-4 seconds on each press. Automatic oiling system will keep the bar and chain constantly lubricated.
Why is oil coming out of my muffler on my chainsaw?
Dripping oil from the exhaust is an indication of several things that could be going on. Most commonly either the fuel is stale or mixed incorrectly or incorrect oil. Next is maintenance of the unit, air filter restricted, spark arrestor, carburetor adjustment.
How do you adjust the oil on a Stihl chainsaw?
Insert a small flat-head screwdriver into the oil adjustment screw on the underside of the chainsaw. Turn the screw clockwise to increase oil flow or counterclockwise to decrease the oil flow, reveals Stihl USA.