Tightening the screw will tighten the chain, and loosening will loosen the chain. Visit our Chainsaw Chains page to our inventory of available replacement chains and other chainsaw accessories. eReplacementParts.com stocks thousands of parts for many major chainsaw brands, including Echo chainsaw parts.
There are no formulas or concrete rules on how you should tighten your chainsaw chain. Bar oil is going to be consumed at a higher rate, and if the chain is too tight it can also damage the clutch and bearings when you start the chainsaw. A loose chain will simply flop around the bar grooves, and a chain that is too tight will refuse to budge.
After reading this post, you’ll know how tight a chainsaw chain should be, how to adjust it, and how to test that you’ve got it perfect. If you’re unable to pull the chain away from the bar, then your chain is too tight. If you keep trying to tension your chain and you just can’t get it right, you may have the wrong sized chain.
Chainsaw chain tension should be checked and tightened often. A properly stretched chainsaw chain should be a little loose on the guide bar – but not so loose that you can pull the drive links out of the bar nose. Maintaining the proper chain tension is therefore essential because it ensures your chainsaw is safe to use and will last for years to come.
can a chainsaw chain be to tight Related Question:
Can you over tighten a chainsaw chain?
There is a tension screw located near the base of the bar on the chainsaw. To tighten the chain, turn it clockwise, and to loosen turn it counterclockwise. Don’t over-tighten the chain as this could cause it to break.
How tight is too tight for a chainsaw chain?
A properly-tensioned chainsaw chain should still be just a little loose on the chainsaw guide bar, but the chain needs to be tight enough that you can’t pull the drive links out of the bar nose.
Why does chainsaw chain keep coming loose?
Chain Not Set Properly One of the most common reasons why your chain might be coming loose is because it was not set properly. When you go through the steps to tension your chain, you need to finish those steps by setting the tension so it won’t change as you work your saw.
How often should you tighten chainsaw chain?
The chain isn’t actually becoming tighter—instead, as you turn the tensioning pin—it pushes the chainsaw bar out a little bit, which takes up the slack on the chain. During a typical afternoon wood-cutting session that lasts 2 to 4 hours, you may need to tighten the chain two or three times.
Why is my chainsaw blade smoking?
This most commonly is a result of a dull chain and exerting to much pressure on the bar and chain trying to make the chain saw cut. This could also be either a lack of bar and chain oil ( tank empty, restricted oiler hole ) or an inferior type of oil that is being slung off the chain and not lubricating.
How loose should a chain be?
It should be tight enough that it only allows you to move it up and down about one inch. If it is sagging or much looser than that, you need to tighten that chain up. Chains often loosen when a bike does not have a derailleur. Derailleur is the gear changing mechanism towards the back of the bike.
Is it worth sharpening a chainsaw chain?
Sharpening your chainsaw chain is definitely worth it as a sharp chainsaw chain is easier to work with. It takes less effort to cut through wood and your chain will make cleaner cuts with sharp blades. A chainsaw chain can be sharpened multiple times without much of a cost.
How long does a chainsaw bar last?
Re: how long does a bar last The next, a Granberg, lasted about 2 months. About that time Stihl started using them with the same results. A good bar can be filed a few times on both sides and the tip replaced when needed. They could last almost as long as the saw.
How long should a chainsaw blade stay sharp?
A chainsaw may only need to be sharpened once a year if it is rarely used, but a tool that is frequently used will need to be sharpened regularly to ensure that the blade doesn’t get too dull. On average, a chainsaw blade will retain its sharpness for about 3 hours of actively cutting through wood.
Why does my chainsaw blade go dull so fast?
Is the wood that you’re cutting with the chainsaw particularly dirty? Many chainsaw enthusiasts have noted that their blades dull faster when they’re cutting muddy wood. If the logs that you’re cutting up are muddy, then perhaps that is the sole reason why your blade is dulling too fast.
Can you overheat a chainsaw?
Chainsaw engines run at high temperatures, usually in the summer, so they can quickly overheat. To prevent chainsaws from overheating they must be cleaned regularly. The cylinder and starter both contain air intake areas that pull cool outside air into the engine when it’s running.
How do I know if my chain is too loose?
To find out whether your chain is too long take a look at it from the side with your eyes being level with the chain. A loose chain will sag close to or below the chainstays as the chain hangs between the rear cogs and chainring. The chain might skip as you pedal, or even drop off the gears.
How tight should a single speed chain be?
Chain Tension There should be approximately one half inch of movement in the chain up and down at a point half way between the front and rear sprockets. To change the tension loosen one of the axle-nuts and move the wheel forward or backward slightly and snug it up again.
How do I know if my chain is too long?
Do a simple check on your bike by shifting the chain to the big chainring and the biggest cassette cog; then, push on the end of the derailleur cage (pushing forward) to see how much it will move forward. If it moves just a little, then you’re good. If it moves a lot, then you’ve got too much chain.
Is it better to sharpen chainsaw chain or buy new?
Sharpen before replacing If your chainsaw chain becomes dull after a long lifespan, it will struggle to cut through the wood at the efficiency it once had. This is why, where possible, you should be looking to keep the will be chain sharp, as sharpening a better course of action than sourcing a replacement.