Oh there is a big diff between cutting a live tree at 15 below zero and cutting wet frozen wood the same temp. The biggest thing with frozen wood that helps me is make sure the rakers are the right height,I turn my oiler to the max setting and i use the stihl winter mix bar oil, i cut alot of dead timber lying in farm lanes in the winter for a few of the farmers in the area and these few simple things have always seem to help the life of the chain. I have cut alot of frozen timber maybe cause its frozen about half of the year up north, frozen hardwood cuts alot slower than unfrozen hardwood and the slower the tree grows the slower it cuts but now living abit farther south I find the big problem is most of the stuff around here is on the edge of a big field which means the wind blows alot more dust so the tree has alot more dust/dirt in the wood which knocks the hell out of the chain in the winter time.
Cutting wood requires a sharp chain and frozen wood will dull your chain. Cutting frozen wood with a chainsaw produces a very fine powder that can get caught in other parts of the saw, leaving the gullet empty. It is possible to cut frozen wood with a chainsaw, but it poses many risks and challenges that you won’t run into when cutting wood that is not frozen.
The best solution to cutting frozen wood is to wait until the weather warms to start cutting again. Cutting frozen wood is frustrating because there’s no easy fix. Once you recognize the wear pattern from frozen wood you can make a decision to sharpen every cut or wait for warmer weather.
“On average you bet. first you will cut your rackers more for frozen but it depends on what type of wood and how much water is in the tree when frozen the more water frozen the harder it will cut.” “I think the species of tree has alot to do with the amount of difference in how it cuts below freezing. When I cut beach, it cuts about the same as in the summer, but red oak causes alot of chain vibration when frozen. So I would guess it has to do with the natural water content of the species. Beach has a very low water content, and red oak is high. I think you would find kiln dried wood would cut the same no matter what the temp.” “Reducing your topplate angle to 20°-25° will give more support to the working corner and help your chain stay sharp longer when cutting frozen wood. It doesn`t make your saw cut any faster, just the opposite, but you can cut efficiently longer. You also want to be careful that you don`t have too much sideplate angle for the same reason.”
can you chainsaw frozen wood Related Question:
Is it OK to chainsaw frozen wood?
It’s not impossible to cut frozen wood with a chainsaw, but it is extremely difficult. Cutting wood requires a sharp chain and frozen wood will dull your chain.
Can you cut frozen trees with a chainsaw?
Just plain old wet frozen wood won’t dull a chain . It will however make even the largest saw cut like the chain is on backwards .
Is wood harder to cut when frozen?
Frozen wood cuts a lot harder than non-frozen wood. Hard maple is the worst, but red oak and hickory aren’t much better.
Can you cut frozen lumber?
As wood freezes the water part becomes more important to the cutting. Cutting unfrozen wood is a matter of severing wood fibers. Cutting lightly frozen wood is a matter of cutting a slushy mix.
Will ice dull a chainsaw?
Yes, you can cut ice with your chainsaw. You don’t have to apply any mineral oil to prevent the water from pollution. To prevent the blade from rusting, you will have to look after your chainsaw.
Can you saw frozen logs?
The most difficult time to saw logs is when they are partially frozen because the blade cuts in and out of the frozen material. Sawing partially frozen logs can be done successfully, but will generally require a little slower feed speed in order to monitor each cut.
How do you cut frozen wood?
Since frozen wood is harder than non-frozen wood, you may want to decrease the saw chain’s filing angle by five degrees. Decreasing the chain’s angle increases cutting performance in frozen woods and decreases the wear to your guide bar and saw chain.
Does frozen wood dry?
Yes, it will dry during winter. I’ve been heating with wood for a lot of years in a place where we get very cold winters. In my experience, the RH of the air has a lot to do with how fast wood dries, freezing temps or not.
Is it OK to chainsaw wet wood?
No, it is not bad to cut the wet wood with your chainsaw. Dewdrops, raindrops, or the snow on the wood will not cause any harm to your chainsaw. It is, in fact, much easier to cut through the wet wood than dry wood because the extra moisture on the wood will act as a natural lubricant.
Why does my chainsaw chain dull so quickly?
Dirt Causes A Chainsaw To Dull If you’re cutting through logs and your angle of approach is too steep, a simple cut through could nick dirt or even worse, rocks on the floor causing your chainsaw to jerk, thus dulling.
Is it best to split wood wet or dry?
Although you can split wood while it’s still wet, it is best to let it dry first. The lower the moisture content of the wood, the easier it will be to split because it gives less resistance when it is dry. However, split wood will dry faster than whole logs. There is more to learn about splitting and storing firewood.
What is frozen wood?
Pykrete is a frozen ice composite. Originally made of approximately 14% sawdust or some other form of wood pulp (such as paper) and 86% ice by weight (6 to 1 by weight).
Can chainsaws cut in water?
No, you can not run a chainsaw in the water. You can work in the rain and wetlands, but you cannot submerge a regular chainsaw underwater to cut anything under the water surface. If you submerge a gas-powered chainsaw underwater, the water will get into the engine and ruin your chainsaw.
What type of chainsaw chain cuts the fastest?
A full chisel chain is a chain with square cornered teeth, and they’re known for being the fastest cutting blade shape available. A full chisel chain also has a higher number of teeth than other chain options(full chisel is also known as a standard chisel chain).
How do you cut a hole in ice without an auger?
Try using a spud bar or digging iron Spud bars and digging irons are long, heavy, iron rods with either a pointed tip or chiseled end. They are great for testing ice thickness, but they can also be used to break open a hole for fishing. What is this? Like the axe, you will be chipping out the ice to make a hole.