This Amsoil 2 stroke oil is a very suitable oil for chainsaw engines. Yes,2 stroke oil or 2 cycle oil is the same type of oil specially designed for 2 stroke or 2 cycle engines. For keeping the productiveness and efficiency of your chainsaw engine and to maximize the engine life, you just need to use the right 2 stroke oil for the chainsaw engine.
Chainsaw bar oil is a necessary component to operating your chainsaw at peak efficiency and with safety in mind. Formula Chainsaw bar oils are either petroleum-based or bio-based. ‘ Chainsaw bar oil for winter is usually 10W. Very hot temperatures may call for a thicker chainsaw oil, in the 40W to 50W range.
Oil is one component of running a saw that people overthink WAY too much. I used to run Castrol TTS which here is a relatively expensive air cooled 2 stroke oil. My saws don’t seem to notice either!I’ve pulled a few of my saws down and they’ve all been well lubed internally at 50:1.All I’d recommend is a good quality synthetic oil although I’ve run AGIP semi synthetic a fair bit and that’s a good oil too.
best chainsaw engine oil Related Question:
Which motor oil is best for chainsaw?
Petroleum-based bar oil has been the standard for chainsaws. Lightweight oil is used in winter and heavier oil in summer.
Can I use any 2-stroke oil in my chainsaw?
Modern two stroke chainsaws do not require generic brand oils to operate at temperatures and rpms that are comparable to those of generic brand oils. Our recommendation is to use only high quality two stroke oil designed for air cooled high performance engines when using your modern two-cycle engine.
Will engine oil be OK in a chainsaw?
Is It Ok To Use Used Motor Oil For Chainsaw? It is not recommended to use motor oil on chain saws for safety reasons or concerns about equipment, but some people do not want to use it. The stickier the bar and chain oil is, the longer it stays on the chain.
What weight oil is chainsaw bar oil?
What viscosity is chainsaw bar oil? The viscosity of chainsaw bar oil can vary depending on the formula but 30W is standard. In cold weather, a thin 10W chainsaw oil may be advantageous, while very hot temperatures may require a much thicker 40W or 50W formula.
Can you use 5w30 for chainsaw bar?
Can I Use 5w30 for a Chainsaw Bar? Like 10w30 motor oil, you can use 5w30 oil. However, the thin and low-viscosity SAE5 weight oil will not cling to the chain and chainsaw bar very well in the summer. You may experience a lot of oil loss and a messy worksite if you choose this chainsaw bar oil alternative.
Can you use 10w40 in a chainsaw?
You can but it’s not very good for the chain or the environment. The Husqvarna / Stihl stuff is much thicker and vegetable based so it doesn’t fling off the chain as easily or poison your garden! 10w30. Thicker.
Is synthetic two-stroke oil better?
Synthetic two-stroke oil is better for the environment, producing lower deposits and emissions due to lower ash content. Petroleum-based two-stroke oils include non-lubricant solvents and additives that allow for easier gasoline mixing. These solvents and additives burn at a high clip and produce higher emissions.
Do you mix oil with gas for chainsaw?
Most STIHL gasoline-powered equipment runs on a 50:1 mixture of gasoline and 2-cycle engine oil. Knowing the proper way to mix your fuel is the first step in keeping it running strong and long.
Can you use old motor oil for chainsaw bar?
Some people caution against using motor oil on a chain saw, but not for safety reasons or concerns about equipment. Bar and chain oil is stickier than regular motor oil, so it stays on the chain longer.
Can I use 10w30 instead of bar and chain oil?
As a matter of fact, you can actually use regular 10w30 motor oil on a chainsaw as one of the alternatives in case you don’t have bar and chain oil. That’s because 10w30 oil has enough thickness and viscosity that will allow it to withstand the friction that is happening whenever you are using a chainsaw.
What is special about chainsaw oil?
Chainsaw bar oil has a certain level of “slickness” to it. This slickness keeps the chain spinning at a fast rate without getting slowed down by the friction that occurs when metal rubs against metal. So, if you want to use the “correct” type of bar oil in your chainsaw, consult the manual and use what it suggests.
Can you use transmission fluid for chainsaw bar oil?
On occasion I’ve used tranny fluid to clean out old oil residue in old chainsaws . It works well . In addition to that tranny fluid seems to pump better on some saws with whimpy oilers in cold weather .
Can any oil be used for chainsaw bar oil?
If your manufacturer’s bar and chain oil is unavailable, you can use SAE 30 weight motor oil to lube your chain during the summer and SAE 10 weight during the winter, according to the University of Missouri Extension.
What happens if you run a chainsaw without bar oil?
Without lubricant, the speed at which the chain moves over the chainsaw bar can cause some serious friction. A slowed-down chain and excessive fuel burning mean there’s a lot of friction between your bar and chain, which means a lot of heat is being produced that could do major damage to your saw.
What does 10W30 mean?
The 10W30 designation on engine oil means that the viscosity of the oil is rated at 10W when an engine is cold, and 30 when the engine is hot. This is different than an oil labelled 5W30, which has a thinner viscosity when the engine is cold at 5W.