Chainsaw bar oil is a necessary component to operating your chainsaw at peak efficiency and with safety in mind. Formula Chainsaw bar oils are either petroleum-based or bio-based. ‘ Chainsaw bar oil for winter is usually 10W. Very hot temperatures may call for a thicker chainsaw oil, in the 40W to 50W range.
Husqvarna Premium Bar and Chain Oil is another ultra-popular premium bar and chain oil. STP Tools Bar and Chain Oil is another ‘premium’ chain bar oil that has thousands of reviews. Mag 1 Bar and Chain Oil is another cheap bar and chain oil that comes by the gallon and will not have any trouble getting the job done.
best biodegradable chainsaw oil Related Question:
Is chainsaw oil biodegradable?
Readily biodegradable, petroleum-free lubricants based on canola oil�including hydraulic fluids, greases, motor oils, concrete release oils, two-cycle oils, and chainsaw-oils are now available commercially in North America.
What oil is best for chainsaw chain?
Petroleum-based bar oil has been the standard for chainsaws. Lightweight oil is used in winter and heavier oil in summer.
Is bar and chain oil bad for the environment?
Environmentally friendly – Using vegetable oil as chain lubricant poses no threat to the environment. Effective – Vegetable oils have natural properties including good lubricity, resistance to shear, a high flash point, and a high viscosity index.
What is chainsaw bar oil made of?
Formula. Chainsaw bar oils are either petroleum-based or bio-based (formulated using vegetable oil). In the course of using a chainsaw, oil sling is inevitable.
Can I use 10w30 for chainsaw bar oil?
As a matter of fact, you can actually use regular 10w30 motor oil on a chainsaw as one of the alternatives in case you don’t have bar and chain oil. That’s because 10w30 oil has enough thickness and viscosity that will allow it to withstand the friction that is happening whenever you are using a chainsaw.
Can you use 10w40 in a chainsaw?
You can but it’s not very good for the chain or the environment. The Husqvarna / Stihl stuff is much thicker and vegetable based so it doesn’t fling off the chain as easily or poison your garden! 10w30. Thicker.
Can any oil be used for chainsaw bar oil?
Generally, chainsaws can handle a wide range of lubricants. Vegetable and canola oils work well, and automobile motor oil will too, as long as you observe the SAE ratings and use the appropriate oil weight for the season. Always use fresh, never used, oils.
Do Electric chainsaws need bar oil?
Electric chain saws derive their power from an electric source, so they don’t need fuel to run. Most gas chain saws require a premixed gas-and-oil fuel to operate properly. Electric chain saws don’t require this added oil, but the bar and chain do need to be properly lubricated.
What happens if you run a chainsaw without bar oil?
Without lubricant, the speed at which the chain moves over the chainsaw bar can cause some serious friction. A slowed-down chain and excessive fuel burning mean there’s a lot of friction between your bar and chain, which means a lot of heat is being produced that could do major damage to your saw.
Can you use old motor oil for chainsaw bar?
Some people caution against using motor oil on a chain saw, but not for safety reasons or concerns about equipment. Bar and chain oil is stickier than regular motor oil, so it stays on the chain longer.
What does 10W30 mean?
The 10W30 designation on engine oil means that the viscosity of the oil is rated at 10W when an engine is cold, and 30 when the engine is hot. This is different than an oil labelled 5W30, which has a thinner viscosity when the engine is cold at 5W.
What is special about chainsaw oil?
Chainsaw bar oil has a certain level of “slickness” to it. This slickness keeps the chain spinning at a fast rate without getting slowed down by the friction that occurs when metal rubs against metal. So, if you want to use the “correct” type of bar oil in your chainsaw, consult the manual and use what it suggests.
Can you use 2 stroke oil as chainsaw oil?
Modern two stroke chainsaws do not require generic brand oils to operate at temperatures and rpms that are comparable to those of generic brand oils. Our recommendation is to use only high quality two stroke oil designed for air cooled high performance engines when using your modern two-cycle engine.
What kind of oil does a ego chainsaw use?
OVERVIEW. The EGO POWER+ 32 Fl Oz Premium Bar and chain lubricant is recommended for use with EGO POWER+ Chain Saws to extend bar and chain life for superior performance. The premium oil-free formula outperforms traditional bar and chain oils and is 100% bio-based and biodegradable.
What is sae30 oil?
The SAE 30 oil is a single grade oil with a viscosity rating of 30. It’s called a single grade (or monograde) oil because it only has one viscosity grade. This is different from a multi grade oil, like 10W-30, which is rated for both SAE 10W and SAE 30.