This is different than the oil that you mix with your gas to provide lubrication to the engine, and I’m going to describe below the importance of this task and explain how to oil your chainsaw for both the safety and care of your saw. Most saws come with a sample bottle of oil and suggestions of which oil to by- but for the most part, the oil is that same from one brand to the next. Saws are designed to feed oil as it runs, so most tanks are large enough to hold enough oil for a full tank of gas.
Check and replace bar and chain oil regularly to reduce friction, keep the saw from wearing out faster, and to make cutting easier. Be sure to use bar and chain oil, Not regular motor oil. Gas chainsaws use about one tank of bar and chain oil for every tank of fuel, so fill the reservoir every time you fill the tank.
At Gardening Products Review, we highly recommend oil manufactured for this specific use. Chainsaw shown in this video tutorial is the Redback 40V 12″ Li-Ion Cordless Chainsaw. The bar & chain oil featured in this video is Husqvarna Bar & Chain Oil – 1 Gallon.
how to oil chainsaw chain Related Question:
Do you need to oil chain on chainsaw?
You want lubrication of the actual chain against the bar. You don’t want to chain to burn – which is what might happen if there’s too much friction. Without oil, it causes frictional force on the motor in the chainsaw as well.
What oil do you use to lubricate a chainsaw chain?
Rapeseed-based (usually called canola) oil is currently the most common environmentally compatible chain-and-bar lubricant. Vegetable-based oils are triglycerides or natural esters that come from agricultural crops.
How often should I oil my chainsaw chain?
Gas chainsaws use about one tank of bar and chain oil for every tank of fuel, so fill the reservoir every time you fill the tank.
Can I use 10w30 for chainsaw bar oil?
As a matter of fact, you can actually use regular 10w30 motor oil on a chainsaw as one of the alternatives in case you don’t have bar and chain oil. That’s because 10w30 oil has enough thickness and viscosity that will allow it to withstand the friction that is happening whenever you are using a chainsaw.
Can I use WD40 as chainsaw oil?
No. You should never use WD40 as chain lubricant since WD-40 is NOT a true lubricant. WD40 is primarily a solvent or rust dissolver.
Is chainsaw oil the same as motor oil?
Bar and chain oil is stickier than regular motor oil, so it stays on the chain longer. Motor oil flings off the chain more quickly, so if you try Terry’s tip, be prepared to refill the oil on your chain saw more quickly than with regular bar and chain oil.
What is special about chainsaw oil?
Chainsaw bar oil has a certain level of “slickness” to it. This slickness keeps the chain spinning at a fast rate without getting slowed down by the friction that occurs when metal rubs against metal. So, if you want to use the “correct” type of bar oil in your chainsaw, consult the manual and use what it suggests.
Do electric chainsaws need bar oil?
Electric chain saws derive their power from an electric source, so they don’t need fuel to run. Most gas chain saws require a premixed gas-and-oil fuel to operate properly. Electric chain saws don’t require this added oil, but the bar and chain do need to be properly lubricated.
Can I use 5w30 for bar oil?
Can I Use 5w30 for a Chainsaw Bar? Like 10w30 motor oil, you can use 5w30 oil. However, the thin and low-viscosity SAE5 weight oil will not cling to the chain and chainsaw bar very well in the summer. You may experience a lot of oil loss and a messy worksite if you choose this chainsaw bar oil alternative.
Can I use engine oil as chainsaw Lube?
If your manufacturer’s bar and chain oil is unavailable, you can use SAE 30 weight motor oil to lube your chain during the summer and SAE 10 weight during the winter, according to the University of Missouri Extension.
Can you use transmission fluid for chainsaw bar oil?
On occasion I’ve used tranny fluid to clean out old oil residue in old chainsaws . It works well . In addition to that tranny fluid seems to pump better on some saws with whimpy oilers in cold weather .
What is the best thing to clean a chainsaw with?
In a well-ventilated area, take a bucket and mix one cup of ammonia with one gallon of water. Place the chainsaw chain in this solution and let it soak for 15 minutes. Put on a pair of thick rubber gloves for protection. Then, use a soft-bristled toothbrush to scrub each section of the chain until it’s free of debris.
What can I do with an old chainsaw?
Gas and oil can be disposed of at a household hazardous waste collection site for free. Remove non-metal parts and place in the trash. Metal parts can be recycled as scrap metal.
What happens when you run a chainsaw without bar oil?
Without lubricant, the speed at which the chain moves over the chainsaw bar can cause some serious friction. A slowed-down chain and excessive fuel burning mean there’s a lot of friction between your bar and chain, which means a lot of heat is being produced that could do major damage to your saw.
What weight is chainsaw bar oil?
What viscosity is chainsaw bar oil? The viscosity of chainsaw bar oil can vary depending on the formula but 30W is standard. In cold weather, a thin 10W chainsaw oil may be advantageous, while very hot temperatures may require a much thicker 40W or 50W formula.