how to use chainsaw youtube Related Question:
What should you not do with a chainsaw?
Don’t Cut With Improper Blade Tension A overly loose or tight chain also wears out the drive sprocket and causes rapid chain and bar wear. To determine if your chain is properly tensioned, pull up on the chain. The drive links should still be in the bar groove. If the links come out of the bar, the chain is too loose.
Are chainsaws easy to use?
If you need to do regular maintenance in your backyard, perhaps removing branches here and there or cutting down small trees, then a small gas-powered chainsaw with a 16-to-18-inch bar is an irreplaceable tool. Due to the small weight and size of the chainsaws in that class, they are really easy to use.
Can you cut with both sides of a chainsaw?
A chainsaw is one of the most versatile tools you can own, but it cuts both wood and flesh equally well.
What is the most common chainsaw injury?
The most common hazards associated with chainsaws are injuries caused by kickback, pushback, and pull-in. Kickback is the most common and poses the greatest hazard. Kickback occurs when the rotating chain is stopped suddenly by contact with a more solid area throwing the saw rapidly backward toward the operator.
What size chainsaw do I need to cut firewood?
Many homeowners find that a 14- to 16-inch chainsaw is a good length for them. That’s long enough to limb-up trees, cut down small trees, and cut most firewood, but it’s also short enough that it’s easy to control the saw.
Should you run a chainsaw at full throttle?
Engine Protection Generally, two-stroke chainsaw engines are built to conveniently run at full throttle without an engine breakdown. Therefore, running at any throttle speed below the full throttle is not advised.
Can you cut wet wood with a chainsaw?
Can you cut wet wood with a chainsaw? Yes, you can cut the wet wood with a chainsaw. Besides, there is a misconception that wet wood can impact the chainsaw bar and chain. But actually, the damp wood will not dull the chainsaw any faster than using it on other types of wood.
What happens if you run a chainsaw without bar oil?
Without lubricant, the speed at which the chain moves over the chainsaw bar can cause some serious friction. A slowed-down chain and excessive fuel burning mean there’s a lot of friction between your bar and chain, which means a lot of heat is being produced that could do major damage to your saw.
Are electric chainsaws safer?
Safer to Use Electric chainsaws have several features that make them safer for casual users than their gas-powered counterparts: Lower chain speeds. Chains that run only when you’re actively cutting with your saw. Bars that measure no longer than 18 inches.
What weight oil is chainsaw bar oil?
What viscosity is chainsaw bar oil? The viscosity of chainsaw bar oil can vary depending on the formula but 30W is standard. In cold weather, a thin 10W chainsaw oil may be advantageous, while very hot temperatures may require a much thicker 40W or 50W formula.
Where is the kickback zone on a chainsaw?
The Kickback Danger Zone The term “kickback danger zone” refers to the top of the tip of the chainsaw bar. This area has a high kickback risk. You should never saw using this part of the chain saw bar, since doing so will significantly increase the chances that you will experience kickback.
How do I stop my chainsaw from pinching?
To stop your chainsaw from getting stuck, make a cut on top of the log or tree that’s preferably one-third of the log’s diameter. Use your chainsaw to cut from the underside until you meet the initial top cut. Always stand on the side when cross-cutting to prevent injury.
Can you use a chainsaw to cut tree roots?
Once you’ve sliced the stump almost all the way to the ground, continue cutting it — and the soil — diagonally and at different angles. Don’t go more than a foot into the soil. Chainsaws are powerful machines, and you don’t have to worry about dirt damaging it or knocking the chain off.
What do you put on tree limbs after cutting?
Pruning sealer, or pruning paint, is simply a petroleum-based waterproof product that is “painted” onto the exposed area of a limb or branch after it has been pruned. The idea is that the application works as a kind of “bandage”, which once painted on allows the tree to heal underneath it.
How much of a tree can you cut without killing it?
As a general rule, don’t prune off more than 15% of the foliage. If you must make space for other plants, it is a better idea to remove a tree completely than to risk over-pruning it.