The correct carburetor adjustment will allow the saw to produce maximum power, extend the duty cycle of the engine, produce minimal smoke, idle smoothly, rev up nicely and give trouble free service. High Speed Fuel Adjustment – This is the adjustment that controls the proportion of fuel in the combustible air/fuel mixture at cutting speed. If carburetor adjustment is required due to a new or rebuilt carburetor, it is best to start with the fuel adjustment settings one turn out.
If you have a new saw, this won’t apply to you, as new regulations require saws to be built so that only a qualified technician can tune the carburetor. If you have an older saw, here’s how to quickly tune it yourself. Less than five minutes of your time can make a big difference in how well your saw runs.
It would not be accurate to say this is the most important setting, because all of these adjustments need to be accurate for a saw to perform its best, but this is the adjustment that determines how the saw runs in the cut. If you adjust your saw with a dirty air filter, the saw will run too lean when the filter is cleaned. If proper adjustment for your saw is outside the limited range, take your saw into a shop.
Insert a small flat-head screwdriver into the idle speed screw and turn it clockwise to increase the engine speed if it idles too slowly. As soon as the chain starts to move, turn the screw counterclockwise until the engine idles without dying and the chain stops moving for the correct idle speed. Adjust the screw labeled ‘L’ until the chainsaw accelerates smoothly and sounds smooth.
how to adjust chainsaw high low Related Question:
How do you adjust a high and low carburetor?
Step 1. Locate the two fuel-adjustment screws on the side of the carburetor. One will be labeled “Hi” and the other “Lo.” The “Hi” screw regulates the engine at full throttle and the “Lo” regulates the fuel when the engine is idling.
How do you adjust the H and L on a Stihl chainsaw?
Determine the carburetor type before adjusting the high- and low-speed screws. To do this, turn the “L” screw clockwise as far as it will go, using a flat-head screwdriver, then turn it counterclockwise as far as it will go.
What does L and H mean on chainsaw?
The letters on the screws represent High (H), Low (L) and Idle (T). The H screw regulates the Air/Fuel mix during high RPMs, while the L Screw does the same during low RPMs.
What is a Stihl 311y?
The MS 311 is a high-tech workhorse with a step up in horsepower and features over the MS 291. With our improved engine technology, you get higher fuel economy for longer run times. The MS 311 also has larger fuel and oil tanks for even longer extended use. You’ll stay productive – while you’re saving money on fuel.
What is the La adjustment on a Stihl?
The LA setting on Stihl chainsaws is controlled by a screw on the outer housing of the engine that adjusts the flow of fuel and air through the carburetor. This screw is inside the engine housing on the carburetor, but is accessible through a hole or gap in the outer housing of the saw.
Why does my chainsaw bog down when I give it gas?
If your chainsaw is bogging down when you give it throttle, this is often a sign of improper gas-to-oil ratio. If there is too much gasoline in relation to the amount of oil used, this is known as a “rich mixture” and can cause the chainsaw to run poorly.
Why does my chainsaw dies at full throttle?
If the filter becomes clogged, not enough fuel will reach the engine for it to run properly. Because your chainsaw will idle, but dies when it is revved up to full power, it means that the filter is only partially clogged; it will allow enough fuel to the engine to run on idle, but not enough to sustain full throttle.
Why does my chainsaw keep cutting out?
The main culprit behind a chainsaw engine that keeps cutting out is usually a dirty or wrongly adjusted carburetor. A faulty carburetor fails to supply the correct air-fuel mixture, also called the “charge”, to the engine. Causing the engine to cut out or stall.
Why does a chainsaw cut crooked?
One major reason a chainsaw curves to either the right or left during a cut is that it was unevenly sharpened. The unequal teeth of the chain cause it to take a different-sized bite into the wood. What is this? The uneven sharpness of the chain is mainly due to manual sharpening, especially with the use of a file.
What are the two adjustment screws on a carburetor?
There should be two screws on the front of the carburetor, which are used to adjust the air and fuel mixture. Often these look like flat-head screws and you can use a screwdriver to turn them, adjusting the amount of fuel and air mixing in the carb.
Why does my chainsaw only runs on choke?
When your chainsaw only runs if the choke is on the problem, in most cases, is a result of fuel supply problems or a faulty carburetor. To fix the problem you should check and clean the fuel system and carburator.
Why does my Husqvarna chainsaw stall?
A clogged carburetor is often caused by leaving fuel in the chainsaw for a long period of time. Over time, some of the ingredients in the fuel may evaporate, leaving behind a thicker, stickier substance. This sticky fuel can clog up the carburetor and cause the chainsaw engine to stall.
Is a ms311 a pro saw?
They aren’t a “professional” grade saw, but they are good. Very relaible, and that’s probably the most important thing with a chainsaw.
What does the HL and La mean on a Stihl chainsaw?
One marked “H”, for high speed, one marked “L”, for low speed and one marked “LA”, which is your low speed air adjustment for idle.
What does H and L stand for on a Stihl chainsaw?
They are typically labeled L (low speed jet), H (high speed jet), and I (idler jet).