The next iteration of chainsaw oiler was still manual, and because it involved an onboard thumb plunger next to the throttle, it eliminated the need for a “Chainsaw caddy.” This advancement in chainsaw oiling technology allowed the operator to manually pump oil onto the bar while cutting. If the chain spits small amounts of oil onto the wood, you’ll know that your chainsaw oiler is functioning properly. As always, if you’ve got any other pro-tips on how to keep your chainsaw oiler functioning properly, feel free to leave them in the comments section below!
Chainsaw oiler consists of an oil pump, oil lines, and oil holes. With the oiler system cleaned from all the debris and gunk, reassemble everything and start your Chainsaw. For electric chainsaw models, you should examine the oiler after each use and make sure it gets replenished when empty.
In this article I’m going to explain why it’s important to keep the chain lubricated and how chainsaw oilers work. With manual oilers you need to release oil onto the chain, usually by pressing a pump button. Some chainsaws come with automatic oilers which allow you to adjust the flow rate of the bar oil.
If your chainsaw is new or you have replaced your chain and guide bar, you will need to keep adjusting the oiler until you determine the right setting that will enable the oiler to produce just the right amount of lubrication. If the above fixes do not work or oiler problems keep recurring, this could indicate that your oiler may be damaged. To ensure that the oiler is functioning correctly, start the chainsaw and let it run for a few minutes then direct the tip of the chainsaw blade towards a piece of wood.
how does a chainsaw automatic oiler work Related Question:
How does an automatic chain oiler work on a chainsaw?
But how does a chainsaw oil pump work? The crankshaft drives the pump, which draws oil from the tank and pushes it onto the guide bar via the outlet hole. The movement of the chain then distributes the oil along the entire length of the guide bar.
What is an automatic oiler?
Many homeowner-grade chainsaws use what are known as true automatic oilers, also called fixed flow oilers. As their name suggests, automatic or fixed flow oilers provide a consistent amount of oil whenever the saw is running. Any time you use your saw, you’ll get the same amount of oil on your chain.
How do you adjust a chainsaw oiler?
To increase the oil flow, turn the automatic oiler adjustment screw counterclockwise. To decrease oil flow, turn the automatic oiler adjustment screw clockwise. While always wearing heavy work gloves, grasp the chain and pull it towards the nose of the chainsaw to ensure that the chain moves freely.
Why is my chainsaw using so much oil?
What causes a chainsaw to leak oil? As the oil is pumped from the tank through to the guide bar, air begins to replace the space where the oil was previously stored. If there isn’t proper ventilation of the oil tank, a vacuum can occur and reduce the flow of oil to the guide bar.
Is it normal for a chainsaw to leak bar oil?
In all but very exceptional cases there is nothing wrong with the chainsaw and what appears to be an oil leak is simply oil that has sprayed from the chain as it rotates at high speed, draining from the saw body and guide bar.
Does a chainsaw need oil?
Both gas and electric chainsaws need oil. Oil helps the smooth and hitch-free performance of the chain and the engine. A special bar/chain oil is used to lubricate the bar and chain. In the case of a gas engine, oil is used as an engine lube.
Can a oil pump get clogged?
How Do I Know If My Oil Pump Is Clogged? An oil filter that is clogged can be one of the causes of poor performance. There is a metallic noise that is audible. The oil pressure is low.
How long do oil pumps last?
You’ll want to check your owner’s manual or the manufacturer’s information online to see how long your particular oil pump should last. Keep in mind that it’s either time or the number of miles, whichever comes first. If you use 12,000 miles per year as a guide, a typical oil pump should last between 5 and 5.84 years.
How do I know if my oil sensor is bad?
The best way to test if your sensor is bad is through the lights on the oil pressure gauge. If the low oil pressure warning light comes on when they engine’s oil levels are normal and your engine is running smoothly and quietly, then you likely have a bad oil pressure sensor.
Can you over oil a chainsaw?
Although a chain saw always requires the moisture that oil provides during the saw’s operation, too much oil isn’t good. When the oil adjustment is set too high, the oil is subject to drip from the chain and run down the guide bar.
Why does my Husqvarna chainsaw leak oil when stored?
The oil must be of a viscosity that adheres to the chain without being too thick or too thin. If you’ve chosen the wrong oil for the machine, that may be the reason it’s leaking from the bottom. Husqvarna strenuously warns users to never use waste oil in a chain saw.
How often should I oil my chainsaw?
Gas chainsaws use about one tank of bar and chain oil for every tank of fuel, so fill the reservoir every time you fill the tank.