Learning how to prevent your chainsaw from pinching when you’re cutting firewood is something everyone should understand. There are two easy techniques I like to use to prevent a chainsaw from pinching when the tree or tree top is already on the ground and you’re ready to cut it up into firewood sized pieces. Placing small pieces of firewood under the tree or using wedges are two easy ways to prevent your chainsaw from pinching when you’re cutting up a tree for firewood that’s already on the ground.
Imagine someone doing a split, where one leg is the tree trunk, the other is the roots that are still going into the ground, and you’re gonna kick that first leg out. 2) Rig the roots/stump to another tree or something solid so that you are applying tension away from the side you will be standing on. 5) The bottom side of the trunk should be in tension and the top side in compression.
Laziness has resulted in my chain and bar getting pinched in the compression side of a log on more occasions than I like to admit. More often than not, I get my blade and chain caught while trying to cut through a large log. I am down on one knee, the saw is cutting like through butter, and I just don’t want to stop and pound a wedge into the top of the cut to keep it from closing on my saw.
how to avoid chainsaw pinch Related Question:
How do I stop my chainsaw from pinching?
To stop your chainsaw from getting stuck, make a cut on top of the log or tree that’s preferably one-third of the log’s diameter. Use your chainsaw to cut from the underside until you meet the initial top cut. Always stand on the side when cross-cutting to prevent injury.
How do you cut down a tree without a pinching chainsaw?
Placing small pieces of firewood under the tree or using wedges are two easy ways to prevent your chainsaw from pinching when you’re cutting up a tree for firewood that’s already on the ground.
Can you fix a pinched chainsaw bar?
To open pinched rails, mount the bar in a vice and gently tap on the bent rail with a hammer and punch. A flat-blade screwdriver is another tool that can be useful for prying open bent bar rails. Once you’ve got the pinch worked out, test your repair by placing the chain back in the groove.
How do you avoid kickback with a chainsaw?
Stand to side of the cutting path of the chain saw. Position yourself so that you are not near the cutting attachment when the chain saw is running. Know where the bar tip is at all times. Install a safety tip that covers the nose of the guide bar on the saw to prevent contact with the kickback zone.
Why does my chainsaw dull so fast?
Dirt Causes A Chainsaw To Dull If you’re cutting through logs and your angle of approach is too steep, a simple cut through could nick dirt or even worse, rocks on the floor causing your chainsaw to jerk, thus dulling.
What should you not do when a tree falls off?
When cutting up a felled tree, avoid touching the ground with the chain because even a brief encounter will severely dull the cutting teeth on your chain saw. If possible, cut partially through the tree and then rotate it to cut the rest of the way through.
Does a chainsaw bar wear out?
As a chainsaw bar wears out, you’ll lose cutting accuracy and efficiency. If the same type of cuts that your saw used to breeze through are now taking twice as long, and you’re sure that your chain is sharp enough, you might look at how worn your bar has become. Thankfully, there are a few simple ways to check this.
How do I know if my chainsaw bar needs replacing?
If you are looking for a general idea for how often you should replace a chainsaw bar, a rule of thumb is to replace the bar of your chainsaw once after you have gone through three chains on the same bar.
What is the most common chainsaw injury?
The most common hazards associated with chainsaws are injuries caused by kickback, pushback, and pull-in. Kickback is the most common and poses the greatest hazard. Kickback occurs when the rotating chain is stopped suddenly by contact with a more solid area throwing the saw rapidly backward toward the operator.
Where is the kickback zone of a chainsaw?
The term “kickback danger zone” refers to the top of the tip of the chainsaw bar. This area has a high kickback risk. You should never saw using this part of the chain saw bar, since doing so will significantly increase the chances that you will experience kickback.
Do I cut compression or tension first?
Always cut on the compression side first! The area on the outside of the bend will pull apart when cut. This is the tension side. If you decide to cut this side only, the tree will split apart before the cut can be completed.
What is limbing a tree?
Limbing is the removal of the branches from either standing or downed trees. Bucking is the process of cutting the downed tree into appropriate lengths.
What is bucking a tree?
Bucking a tree The process of cutting a tree into usable lengths is called bucking. Bucking often occurs as a tree is being limbed, such as when the limbs of the crown are to be used as firewood. When cutting firewood, make sure you know the needed length of wood before you leave home.
Why do loggers run upside down bars?
Every chainsaw bar has been designed to be mounted right-side up or upside down. The reason for this is that it allows the user to extend the life of his chainsaw bar by 50%. Flipping the bar will give the heavily-used areas some relief from wear and tear.
Why should we not cut trees?
Ans. We should not cut trees because trees give us oxygen to breathe. Trees are also useful in many other things like, they give us fruits, vegetables, herbs and wood, etc.