It will naturally take longer to cut a large log with a small chainsaw. Another trick when using a small chainsaw to cut a large log is to buy a longer guide bar. If you want to know how to cut a large log with a small chainsaw, you’re not alone.
First cut should cut should be made from the underside towards the top about 1/3 of the way through the log. Once you had assessed the situation, begin to cut the limbs supporting the tree, cut from under these limbs to avoid the chainsaw getting pinched or stuck. Make an initial cut upwards, about 1/3 of the way through the branch, a short distance from the trunk of the tree so you have room for the final cut which will be close to the trunk.
Cutting logs with a chainsaw can seem daunting, especially because it’s one of the first skills learned by chainsaw users. In this guide, we’ll be covering the following 8 steps, which will show you the basics for how to cut logs with a chainsaw. Basically what can happen, is if you hit that part of the chainsaw against a piece of wood, it catches the chain and throws the whole chainsaw back towards the user.
Well whatever the reason is, I’ll be showing you how to cut a large log with a small chainsaw. After you’ve cut as deep as you can into the log, you’re going to roll over the log and re-enter into the cut. You cut a large log with a small chainsaw by making cuts into the logs as deep as possible and then rolling the log onto the other side.
how to chainsaw big logs Related Question:
How big of a tree can a 16 chainsaw cut?
16 chainsaw would cut through a 14″ tree diameter. 10 inch chainsaw for 8″ in diameter. 6 inch chainsaw can cut a 4″ diameter.
How do I stop my pinching chainsaw log?
To stop your chainsaw from getting stuck, make a cut on top of the log or tree that’s preferably one-third of the log’s diameter. Use your chainsaw to cut from the underside until you meet the initial top cut. Always stand on the side when cross-cutting to prevent injury.
What does it mean to buck up a log?
“Buck up” can refer to cutting a felled tree and its branches up into shorter lengths. You may use a sawbuck at the end of the operation; at the beginning, simply prop up a long log to be cut on top of other logs.
What does it mean to buck a log?
Bucking is the process of cutting a felled and delimbed tree into logs. Significant value can be lost by sub-optimal bucking because logs destined for plywood, lumber, and pulp each have their own value and specifications for length, diameter, and defects.
How do you cut a large tree in sections?
Climb back up and locate the wedge cut. Make a straight cut into the tree until the chain goes through to the wedge cut. The top part of the tree should know fall in the direction of the wedge cut. Continue this process down the trunk of the tree cutting it down into manageable sections.
How big of a tree can a 20 inch chainsaw cut?
A good rule of thumb is that the diameter of the trees you cut regularly should be no more than twice the length of the bar on a chainsaw. That means a 20-inch chainsaw can handle a 36-inch tree (remember, effective cutting length is roughly -2 inches of the bar length).
Why does a chainsaw cut crooked?
One major reason a chainsaw curves to either the right or left during a cut is that it was unevenly sharpened. The unequal teeth of the chain cause it to take a different-sized bite into the wood. What is this? The uneven sharpness of the chain is mainly due to manual sharpening, especially with the use of a file.
How do I stop my log slices from splitting?
Thin wood slices soaked in denatured alcohol will dry without shrinking so quickly that cracks form. Fill your container just over halfway full with denatured alcohol so you can soak the slice without the liquid spilling over the sides.
Can you cut logs with a circular saw?
Circular saws are great for cutting plywood and 2x’s, but you can also cut everything from logs to concrete to steel beams with the right blade or the right type of saw.
What is the most common chainsaw injury?
The most common hazards associated with chainsaws are injuries caused by kickback, pushback, and pull-in. Kickback is the most common and poses the greatest hazard. Kickback occurs when the rotating chain is stopped suddenly by contact with a more solid area throwing the saw rapidly backward toward the operator.
How do you cut a log under tension?
A felled tree will usually have saw-pinching areas where the top of the log is under compression and the bottom is under tension. If you have access to the top and bottom of the log, you can handle this one of two ways. Make a cut directly down from the top and then finish by cutting up from the bottom.
Can electric chainsaw cut trees?
Although electric chainsaws are smaller and easier to carry, most lack the power and stamina to cut down large trees. If you have big trees on your property that you want to remove or cut into firewood, a gas model is your best bet. Electric chainsaws come in two types: corded and battery-powered.
Can you cut with the top of a chainsaw?
While it’s designed to cut with either the top or bottom of the blade, just about anything that comes in contact with the top half of the end tip of the blade (known as the kickback zone) can change the cutting momentum and cause the saw to slam back against you.
How are logs turned into boards?
Similar to cant sawing, plain sawing begins with rotating and sawing the outer sides of a log into boards until the center is squared into a four-sided cant. Instead of leaving the cant as is, it is rotated and sawn to produce the maximum amount of lumber.