Important: Always make sure the engine is turned off before you begin tensioning the chainsaw chain. Locate the chain tension adjustment points on your chainsaw. Common locations for adjustment points include the side cover and the front of the chainsaw.
Tightening the screw will tighten the chain, and loosening will loosen the chain. Visit our Chainsaw Chains page to our inventory of available replacement chains and other chainsaw accessories. eReplacementParts.com stocks thousands of parts for many major chainsaw brands, including Echo chainsaw parts.
There are no formulas or concrete rules on how you should tighten your chainsaw chain. Bar oil is going to be consumed at a higher rate, and if the chain is too tight it can also damage the clutch and bearings when you start the chainsaw. A loose chain will simply flop around the bar grooves, and a chain that is too tight will refuse to budge.
After reading this post, you’ll know how tight a chainsaw chain should be, how to adjust it, and how to test that you’ve got it perfect. If you’re unable to pull the chain away from the bar, then your chain is too tight. If you keep trying to tension your chain and you just can’t get it right, you may have the wrong sized chain.
how tight chainsaw blade Related Question:
How tight do you want a chainsaw blade?
A properly-tensioned chainsaw chain should still be just a little loose on the chainsaw guide bar, but the chain needs to be tight enough that you can’t pull the drive links out of the bar nose.
Can you over tighten a chainsaw chain?
There is a tension screw located near the base of the bar on the chainsaw. To tighten the chain, turn it clockwise, and to loosen turn it counterclockwise. Don’t over-tighten the chain as this could cause it to break.
Why is my chainsaw blade smoking?
This most commonly is a result of a dull chain and exerting to much pressure on the bar and chain trying to make the chain saw cut. This could also be either a lack of bar and chain oil ( tank empty, restricted oiler hole ) or an inferior type of oil that is being slung off the chain and not lubricating.
Why does chainsaw chain keep coming loose?
Chain Not Set Properly One of the most common reasons why your chain might be coming loose is because it was not set properly. When you go through the steps to tension your chain, you need to finish those steps by setting the tension so it won’t change as you work your saw.
Why does my chainsaw blade go dull so fast?
Is the wood that you’re cutting with the chainsaw particularly dirty? Many chainsaw enthusiasts have noted that their blades dull faster when they’re cutting muddy wood. If the logs that you’re cutting up are muddy, then perhaps that is the sole reason why your blade is dulling too fast.
How long should a chainsaw blade stay sharp?
A chainsaw may only need to be sharpened once a year if it is rarely used, but a tool that is frequently used will need to be sharpened regularly to ensure that the blade doesn’t get too dull. On average, a chainsaw blade will retain its sharpness for about 3 hours of actively cutting through wood.
Is it worth sharpening a chainsaw chain?
Sharpening your chainsaw chain is definitely worth it as a sharp chainsaw chain is easier to work with. It takes less effort to cut through wood and your chain will make cleaner cuts with sharp blades. A chainsaw chain can be sharpened multiple times without much of a cost.
How long does a chainsaw bar last?
Re: how long does a bar last The next, a Granberg, lasted about 2 months. About that time Stihl started using them with the same results. A good bar can be filed a few times on both sides and the tip replaced when needed. They could last almost as long as the saw.
How many times can a chainsaw chain be sharpened?
Cutters can be sharpened up to 10 times or more before the chain needs replacing. If your cutters are worn unevenly after a few sharpenings, a professional can regrind them to uniform shape. If you use the same chain for a few years, then buy a new one, the new one won’t mesh smoothly with the sprocket and bar.
How often should you flip the bar on your chainsaw?
Some professional loggers would advocate that you should flip your chainsaw bar at the end of every use, particularly when you are cleaning up. Others suggest a more relaxed approach advising that you flip the chainsaw bar only when you are changing your chainsaw blade.
Why do loggers run upside down bars?
Every chainsaw bar has been designed to be mounted right-side up or upside down. The reason for this is that it allows the user to extend the life of his chainsaw bar by 50%. Flipping the bar will give the heavily-used areas some relief from wear and tear.
Why does my chainsaw cut curves?
Two main reasons will cause the chain to cut on a curve. The most common reason is from improper hand filing. If one side of the teeth is more heavily damaged, sharpening them down will make them smaller than the other side.
Does cutting wet wood dull a chainsaw?
Does Cutting Wet Wood Dull a Chainsaw? Using your chainsaw to cut through wet wood will not dull the chain any faster than using it for other types of wood. When you think about it, your chainsaw chain is already wet. True, it is not wet with water.
Do chainsaw chains stretch over time?
It’s perfectly normal for a chainsaw chain to stretch after regular use. But, if you allow your chainsaw to become too loose, it can easily come off and pose a dangerous situation for you. A chainsaw chain stretches and loosens from tension and extreme friction.
Can you drill holes in chainsaw bar?
Re: Drilling a Chainsaw Bar Drilling that bar may not be as difficult as you think. It will be best if you use a drill press, start with a pilot hole, and then drill to the size you need. Make sure you have a sharp bit, run at the lowest speed you can, and use cutting fluid.