The problem is that the chain is so much harder then the bar rails. My advice would be square it up the best you can then use it for stumps and go get yourself a new bar for all your other cutting, its always good to have a stumping bar. If youre gonna try to hand file those rails, clamp your file in a vice and draw the bar across it while pressing down flat against the vice jaws to maintain squareness.
You should know how to dress it well and how to use the chainsaw to cause the least amount of damage to the guide bar. Now let’s talk about how to maintain a good condition of a chainsaw bar -. Take the guide bar out of the saw and check with your eyes while keeping the bar on a flat surface.
If the bar you are using has significant heel wear, your saw probably has a tendency to “Throw” its chain. If you compare a worn bar to a new bar, you will notice the warn bar has a much narrower heel. To inspect a guide bar for damage, first remove it from the saw.
how to dress chainsaw bar Related Question:
Do STIHL chainsaw bars need grease?
A lubricating tool for select STIHL. The Guide Bar Grease Gun is designed for lubricating the sprocket nose bearings on guide bars that have the grease hole. Current STIHL guide bars offer maintenance free sprocket noses, some competitor’s guide bars still require additional grease.
How often should you flip the bar on a chainsaw?
Some professional loggers would advocate that you should flip your chainsaw bar at the end of every use, particularly when you are cleaning up. Others suggest a more relaxed approach advising that you flip the chainsaw bar only when you are changing your chainsaw blade.
Can you drill holes in chainsaw bar?
Re: Drilling a Chainsaw Bar Drilling that bar may not be as difficult as you think. It will be best if you use a drill press, start with a pilot hole, and then drill to the size you need. Make sure you have a sharp bit, run at the lowest speed you can, and use cutting fluid.
Why is my chainsaw bar smoking?
This most commonly is a result of a dull chain and exerting to much pressure on the bar and chain trying to make the chain saw cut. This could also be either a lack of bar and chain oil ( tank empty, restricted oiler hole ) or an inferior type of oil that is being slung off the chain and not lubricating.
How long does a chainsaw bar last?
Re: how long does a bar last The next, a Granberg, lasted about 2 months. About that time Stihl started using them with the same results. A good bar can be filed a few times on both sides and the tip replaced when needed. They could last almost as long as the saw.
Does STIHL make guns?
So Stihl are making pump action shotguns now …
Do Oregon bars need grease?
Most Oregon and Husqvarna bars (photo above) traditionally come with a greasing hole. Most STIHL bars do not. However, STIHL bars are built with thin shims on either side of the bearing/sprocket assembly to help keep debris out.
What kind of oil do you use for a chainsaw?
Petroleum-based bar oil has been the standard for chainsaws. Lightweight oil is used in winter and heavier oil in summer. Manufacturers of chainsaws make bar and chain oils specially blended for their machines to extend their lifespan, but if they are not available, the owner’s manual suggests alternatives.
Do electric chainsaws need bar oil?
Electric chain saws derive their power from an electric source, so they don’t need fuel to run. Most gas chain saws require a premixed gas-and-oil fuel to operate properly. Electric chain saws don’t require this added oil, but the bar and chain do need to be properly lubricated.
When should I oil my chainsaw?
So, whenever you refuel your gas chainsaw, you should add bar and chain oil as well, every time. The steps are quick and easy: Set your chainsaw on a level surface, bar side down so that it lays flat. Allow a minute for the oil to settle, then unscrew the cap to the saw’s bar and chain oil reservoir.
How much bar oil should a chainsaw use?
When to Oil Gas chainsaws use about one tank of bar and chain oil for every tank of fuel, so fill the reservoir every time you fill the tank.
Why do people turn their chainsaw bars upside down?
Every chainsaw bar has been designed to be mounted right-side up or upside down. The reason for this is that it allows the user to extend the life of his chainsaw bar by 50%. Flipping the bar will give the heavily-used areas some relief from wear and tear.
Why does my chainsaw blade dull so quickly?
Is the wood that you’re cutting with the chainsaw particularly dirty? Many chainsaw enthusiasts have noted that their blades dull faster when they’re cutting muddy wood. If the logs that you’re cutting up are muddy, then perhaps that is the sole reason why your blade is dulling too fast.
What chainsaw chains do professional loggers use?
Full-chisel teeth chains are usually used by professionals on large saws. Semi-chisel teeth are rounded, so the risk of kickback is less, and they stay sharper longer. Semi-chisel teeth cut slower but are a better choice in dirty wood than full chisel.
How do I know if my Stihl clutch is bad?
Does the engine loose revs, or the engine keep revving and just the chain stops? If the engine is still running at normal revs, and the chain slows down, then it’s a problem with the clutch. Worn out, gummed up, jammed springs etc. If the engine looses revs under load then it’s more likely a fuel or carb problem.