How to Start a Chainsaw That’s Been Warmed Up.If you’re taking a short break from using the chainsaw, then you can restart it without using the choke since the engine is already primed with fuel. If you haven’t purchased a chainsaw yet, I encourage you to take a look at my best gas chainsaw reviews. Check out my best 18 inch chainsaw page and best 16 inch gas chainsaw page to see what you can get.
The chain brake should be activated when you start the chainsaw. Release the front handle and allow gravity to bring the chainsaw down, rotating around the rear handle, towards the stump. Hold the chainsaw firmly by the front and rear handles.
To clear excess fuel from the carburetor, place the choke lever in the Off position, hold the throttle trigger fully open and pull the starter rope 5 or 6 times. Try to start the chainsaw after priming the carburetor. Activate the choke by moving the lever to the full choke position and pull the starter rope 3 or 4 times to start the engine.
how to start a chainsaw easily Related Question:
How do I make my chainsaw easier to start?
Try to start the chainsaw after priming the carburetor. 5. Activate the choke by moving the lever to the full choke position and pull the starter rope 3 or 4 times to start the engine. If that doesn’t work, move the choke lever to half choke and pull the starter rope, 6 times maximum, to start the engine.
Why is it so hard to pull start my chainsaw?
If your chainsaw is hard to pull, here are some common causes: The pully system is snagged or stuck. The starter assembly is stuck or sticky. The housing may be damaged.
Do you start a chainsaw with the brake on or off?
Check the Chain Brake When engaged, the chain brake stops the chain from rotating around the saw’s guide bar. When using a chainsaw, you should always start it with the chain brake engaged so the chain does not move.
What is the easiest to start chainsaw?
The best gas-powered model, the ECHO 18 in. Gas 2-Stroke Cycle Chainsaw, is easy to start and has impressive cutting power.
Can you start a chainsaw with a cordless drill?
NOTE: A battery-powered drill is often not enough to start your chainsaw fast enough. In that case, use an electric drill plugged in a wall outlet. Sometimes the bolt will strip out and when you crank up, the bolt can come out.
What causes a chainsaw to vapor lock?
Vapor lock occurs when the fuel (usually gasoline) within the fuel delivery system overheats and vaporizes too rapidly. The resulting excess gas bubbles accumulate to the point of actually blocking normal fuel delivery.
How do you rewind a chainsaw pull start?
Feed the cord through the holes in the housing and pulley, and tie a knot in the end. Keep tension on the cord with one hand while you release the pliers with the other. Let the pulley slowly rewind. It will wrap the cord around itself and stop when the handle contacts the housing.
Is there an electric start chainsaw?
We hate to inform you, but gas chainsaws with automatic electric-start systems don’t exist. The mechanism that keeps the saw running—the gas engine—is the same mechanism that gives it the power to start. A special spring is probably the most common easy-start feature you’ll find on chainsaws.
How long does a spark plug last in a chainsaw?
A poorly functioning engine in a Stihl chainsaw can mean more work for the operator and can even be dangerous. Consequently, Stihl recommends replacing the spark plug after every 100 service hours.
Can you use starting fluid on a chainsaw?
Removing the air filter, spraying starting fluid into the carburetor and pulling the starting rope is another quick way to clear out the engine. Starting fluid creates a leaner fuel mixture that ignites more easily, and the operation of the engine clears out the combustion chamber automatically.
How do I know if my chainsaw spark plug is bad?
If it’s not producing any sparks at all, your chainsaw needs a new plug. If there are only a few sparks coming out of one side of the electrodes but none on the other side, it’s not bad enough for you to worry about, but it will affect your performance.
How do you stop vapor lock?
Once the fuel system has cooled, you can help eliminate any vapor left in the fuel system by first pressing the accelerator pedal slightly (do not press it to the floor) while cranking the engine. Once the engine starts, hold the accelerator pedal down until the vehicle runs smoothly, indicating the vapor lock is gone.
Why does my chainsaw flood so easily?
There could be various causes: incorrect fuel mixture, carburation not calibrated properly, or a wet spark plug. In spite of their power and robustness, chainsaws are actually rather delicate machines that require careful and precise maintenance at every stage of their life cycle.
How long does it take to Unflood a chainsaw?
The first option is the easiest since it doesn’t require any effort on your part, it just takes time. Many people wonder if a flooded chainsaw will fix itself? The answer is yes, but not always. By letting the chainsaw sit for about 20 minutes it will allow some of the fuel inside the engine to evaporate.
Will a flooded engine fix itself?
Will a flooded engine fix itself? No. You have to take appropriate measures to restore the fuel and air balance in your car’s engine.