The correct carburetor adjustment will allow the saw to produce maximum power, extend the duty cycle of the engine, produce minimal smoke, idle smoothly, rev up nicely and give trouble free service. High Speed Fuel Adjustment – This is the adjustment that controls the proportion of fuel in the combustible air/fuel mixture at cutting speed. If carburetor adjustment is required due to a new or rebuilt carburetor, it is best to start with the fuel adjustment settings one turn out.
If you have a new saw, this won’t apply to you, as new regulations require saws to be built so that only a qualified technician can tune the carburetor. If you have an older saw, here’s how to quickly tune it yourself. Less than five minutes of your time can make a big difference in how well your saw runs.
How to Adjust the Carburetor on a Poulan Pro Chainsaw. Adjusting the Homelite chainsaw carburetor involves tuning the idle speed screw. Adjust the screw labeled ‘L’ until the chainsaw accelerates smoothly and sounds smooth.
A carburetor is an exceptional part of a chainsaw that controls the quantity of fuel used by the machine. If you adjust the chainsaw with low fuel, when you fill-up the tank eventually, the carburetor may become too adjusted. Because the carburetor is a key piece to the chainsaw, it is a good idea to know how to adjust it.
how adjust carburetor for chainsaw Related Question:
Why does my chainsaw stall when I give it gas?
If the filter becomes clogged, not enough fuel will reach the engine for it to run properly. Because your chainsaw will idle, but dies when it is revved up to full power, it means that the filter is only partially clogged; it will allow enough fuel to the engine to run on idle, but not enough to sustain full throttle.
What is the H and L on a carburetor?
This adjustment controls the fuel flow to the low speed or idle circuit. If the carburetor is too far out of adjustment to run, or has been disassembled, start with turning the L and H all the way in and then open 2 turns on each needle. Then turn the TAS screw or idle speed adjustment in all the way.
How do you know if your chainsaw is running lean?
If your chainsaw is running lean, it will take a long time to return to idle once you rev it up at a high rpm. Idle means the chain isn’t spinning even though the engine is on. Also, the saw will work at a higher rpm than recommended, but it will have less cutting power due to the lack of gas in the mixture.
What are the L and H screws on chainsaw?
The letters on the screws represent High (H), Low (L) and Idle (T). The H screw regulates the Air/Fuel mix during high RPMs, while the L Screw does the same during low RPMs.
Why does my chainsaw start but wont stay running?
A clogged fuel filter will starve your chainsaw’s engine, and it can also damage it by letting contaminated fuel into the engine. Bad fuel can also clog the carburettor. Clogged carburettors are one of the most common reasons why a chainsaw won’t stay running or start at all.
Why does my Stihl chainsaw bog down when I give it gas?
The Job of the Carburetor One controls the fuel mixture when the engine is idling, one controls it when the engine is operating at low speed and one is for high-speed fuel control. When the saw bogs down during cutting, it’s usually the high-speed screw you need to adjust.
Why does my chainsaw only runs on choke?
When your chainsaw only runs if the choke is on the problem, in most cases, is a result of fuel supply problems or a faulty carburetor. To fix the problem you should check and clean the fuel system and carburator.
How do you adjust the H and L on a Stihl chainsaw?
Determine the carburetor type before adjusting the high- and low-speed screws. To do this, turn the “L” screw clockwise as far as it will go, using a flat-head screwdriver, then turn it counterclockwise as far as it will go.
Why does my chainsaw keep bogging down?
Many chainsaw operators first notice a problem with chainsaws bogging down when they’re using the chainsaw under load, and this is usually the result of poor air circulation. This issue is caused by a clogged air filter on the chainsaw. Remove the air filter from the chainsaw.
How do I get my chainsaw to idle?
1 – When the saw is warm and not running, turn the adjusting screw in (clockwise) a half turn, start the saw, repeat this process until the saw idles. 2 – The saw now idles, great! But it should idle without the chain moving.
How do I know if my chainsaw carburetor is bad?
The carburetor might need to be replaced. To test the carburetor, remove the air filter, pour a teaspoon of fuel into it, and pull the starter rope. If the engine starts momentarily and then dies, the carburetor is likely why the chainsaw won’t start.
Why does my Poulan chainsaw dies when I give it gas?
The carburetor might be clogged. A clogged carburetor is often caused by leaving fuel in the chainsaw for a long period of time. Over time, some of the ingredients in the fuel may evaporate, leaving behind a thicker, stickier substance. This sticky fuel can clog up the carburetor and cause the chainsaw engine to stall.
How do you adjust a Stihl carburetor?
Turn the H screw clockwise with a carburetor adjustment tool until the head is spinning as fast as it will go, then back off the screw carefully until the RPMs start to decrease. Turn the screw slowly clockwise again until the engine once again just starts to pick up speed.
How do you start a stubborn chainsaw?
Try to start the chainsaw after priming the carburetor. 5. Activate the choke by moving the lever to the full choke position and pull the starter rope 3 or 4 times to start the engine. If that doesn’t work, move the choke lever to half choke and pull the starter rope, 6 times maximum, to start the engine.
What happens when you run straight gas in a chainsaw?
If straight gas is used, it can damage and ruin the piston and crankcase within a minute, as the gas doesn’t take long to burn out these sensitive parts. Drain the tank immediately into a separate fuel container.