Learning how to prevent your chainsaw from pinching when you’re cutting firewood is something everyone should understand. There are two easy techniques I like to use to prevent a chainsaw from pinching when the tree or tree top is already on the ground and you’re ready to cut it up into firewood sized pieces. Placing small pieces of firewood under the tree or using wedges are two easy ways to prevent your chainsaw from pinching when you’re cutting up a tree for firewood that’s already on the ground.
There are various techniques that people use to keep the chainsaw from getting stuck. People usually use the crosscutting process of cutting the wood; with this method, you will get the job done without the chainsaw getting stuck. Using a chainsaw intended for remote work can help limit the danger of your chainsaw from getting squeezed or caught.
Laziness has resulted in my chain and bar getting pinched in the compression side of a log on more occasions than I like to admit. More often than not, I get my blade and chain caught while trying to cut through a large log. I am down on one knee, the saw is cutting like through butter, and I just don’t want to stop and pound a wedge into the top of the cut to keep it from closing on my saw.
how to keep your chainsaw from getting pinched Related Question:
How do I stop my chainsaw from pinching?
To stop your chainsaw from getting stuck, make a cut on top of the log or tree that’s preferably one-third of the log’s diameter. Use your chainsaw to cut from the underside until you meet the initial top cut. Always stand on the side when cross-cutting to prevent injury.
How do you cut down a tree without a pinching chainsaw?
Placing small pieces of firewood under the tree or using wedges are two easy ways to prevent your chainsaw from pinching when you’re cutting up a tree for firewood that’s already on the ground.
Can you fix a pinched chainsaw bar?
To open pinched rails, mount the bar in a vice and gently tap on the bent rail with a hammer and punch. A flat-blade screwdriver is another tool that can be useful for prying open bent bar rails. Once you’ve got the pinch worked out, test your repair by placing the chain back in the groove.
Why does my chainsaw dull so fast?
Dirt Causes A Chainsaw To Dull If you’re cutting through logs and your angle of approach is too steep, a simple cut through could nick dirt or even worse, rocks on the floor causing your chainsaw to jerk, thus dulling.
What is bucking a tree?
Bucking a tree The process of cutting a tree into usable lengths is called bucking. Bucking often occurs as a tree is being limbed, such as when the limbs of the crown are to be used as firewood. When cutting firewood, make sure you know the needed length of wood before you leave home.
What should you not do when a tree falls off?
When cutting up a felled tree, avoid touching the ground with the chain because even a brief encounter will severely dull the cutting teeth on your chain saw. If possible, cut partially through the tree and then rotate it to cut the rest of the way through.
How do most chainsaw accidents happen?
The most common hazards associated with chainsaws are injuries caused by kickback, pushback, and pull-in. Kickback is the most common and poses the greatest hazard. Kickback occurs when the rotating chain is stopped suddenly by contact with a more solid area throwing the saw rapidly backward toward the operator.
What are metal bucking spikes on a chainsaw?
Bumper Spikes: This series of sharp metal spikes protruding from the saw near the base of the bar provide leverage for easier, more controlled sawing. Jab the spikes into the log, then pivot the bar downward to guide the chain through the cut.
Where is the kickback zone of a chainsaw?
The term “kickback danger zone” refers to the top of the tip of the chainsaw bar. This area has a high kickback risk. You should never saw using this part of the chain saw bar, since doing so will significantly increase the chances that you will experience kickback.
Does a chainsaw bar wear out?
As a chainsaw bar wears out, you’ll lose cutting accuracy and efficiency. If the same type of cuts that your saw used to breeze through are now taking twice as long, and you’re sure that your chain is sharp enough, you might look at how worn your bar has become. Thankfully, there are a few simple ways to check this.
How often should you flip the bar on a chainsaw?
Some professional loggers would advocate that you should flip your chainsaw bar at the end of every use, particularly when you are cleaning up. Others suggest a more relaxed approach advising that you flip the chainsaw bar only when you are changing your chainsaw blade.
How long should a chainsaw blade stay sharp?
A chainsaw may only need to be sharpened once a year if it is rarely used, but a tool that is frequently used will need to be sharpened regularly to ensure that the blade doesn’t get too dull. On average, a chainsaw blade will retain its sharpness for about 3 hours of actively cutting through wood.
Why do loggers run upside down bars?
Every chainsaw bar has been designed to be mounted right-side up or upside down. The reason for this is that it allows the user to extend the life of his chainsaw bar by 50%. Flipping the bar will give the heavily-used areas some relief from wear and tear.
Do I cut compression or tension first?
Always cut on the compression side first! The area on the outside of the bend will pull apart when cut. This is the tension side. If you decide to cut this side only, the tree will split apart before the cut can be completed.
Do you start a chainsaw with the brake on?
When using a chainsaw, you should always start it with the chain brake engaged so the chain does not move.