“After starting a hole in the ice with your spud, you must switch to your chainsaw and angle its blade as you cut. To cut a straight line in the ice, you should keep the blade of your chainsaw at a forty-five degree to a sixty degrees angle, not straight upward and downward, and make the cuts in ice as you push its blade into the ice, not while you draw it backward,” Thompson said. The lessons learned over the years with my chainsaw include; before shutting the chainsaw off, I always walk a distance away from the group of my students and rev the chainsaw up to clear any water, then it is shut off and place up off the ice. “My chainsaw is more than thirty years old and, now I am using it on ice only. It looks and runs like a brand new one. Check the length of the board, its appropriate distance, and then use the chainsaw to cut another hole in the ice ahead of the board. If you notice sawdust on the ice, you should stop immediately as the board is being cut, so you should quickly move further away.”
Consider the ice thickness and the safety of using a chainsaw to prevent any injuries or falling into the ice if it were too thin. You can go for specialized ice-cutting tools such as ice augers, which are used for cutting circulation holes in the ice. Once you have cut through the ice, use an ice bar or pick when extracting larger ice out.
When you running your saw on the ice for the first time of the season, do a bunch of cutting before you get to your spot. That will flush and clean out your “Ice saw” so when you actually get to your spot you hole is nice and clean with no oil slick…. I screw in a T ice anchor before cutting as an aid to lift the block up and out before cutting… Make your cuts at a slight angle so your block can only come out one way. Ever since I bought my ice saw I have never needed the chainsaw for cutting a spear hole.
Poor choice of tools, last time I was on the ice after someone used a chain saw the whole was so big my dog feel in it, poor choice and taste. There were a couple of huge chunks of ice that were cut out and just left on top of the ice. Used to chop hole through the ice with an axe for the old man as a kid got real messy real fast tried the saw thing too and found that using the top of the saw works better as the chips and water are thrown the opposite direction Please mark any such holes with large branches frozen into it sticking up……. Thread Tools Posting Rules.
how to chainsaw ice Related Question:
How do you cut ice?
Using your ice pick to hold the ice in place, use your knife to gently saw a line across the center of the block ice. If your ice is rectangular, you should saw widthwise; if your ice is square, saw a line across the middle. Essentially you’re marking the ice in order to cut it cleanly in half.
How do you cut a hole in ice without an auger?
Try using a spud bar or digging iron Spud bars and digging irons are long, heavy, iron rods with either a pointed tip or chiseled end. They are great for testing ice thickness, but they can also be used to break open a hole for fishing. What is this? Like the axe, you will be chipping out the ice to make a hole.
How do you cut ice without cracking it?
Put your knife back where the line is, hold it in place firmly, and hit your mallet on top of the knife. It may take a few hits to have the ice block split, but it should split cleanly. If not, then likely the ice wasn’t tempered long enough. Wait a couple more minutes and try again.
What bait do you use for ice fishing?
For ice fishing live bait, try wax worms (bee moth larva), maggots, spikes (fly larvae), wigglers (mayfly larvae) or minnows. You can drop your bait and leave it alone, or you can slowly jig to attract the fish. Ice fishing jigging also works with artificial ice fishing bait.
Is it OK to use a chainsaw to cut ice?
Yes, you can cut ice with your chainsaw. You don’t have to apply any mineral oil to prevent the water from pollution. To prevent the blade from rusting, you will have to look after your chainsaw.
What can I use instead of an auger?
A spud bar or digging iron will work fine. I made my spud bars out of rebar and a piece of flat steel that I machined and hardened.
How do you cut lake ice?
Use a Hand Auger “Ice fishing can be kept simple,” says Thielen. “You need a good six-inch hand auger like a Strikemaster Lazer auger, until the ice hits eight inches thick.” Thielen repeated the need to drill down as straight as possible. “It’s much easier to cut through when drilling straight,” he said.
How do you make ice clear when it freezes?
Step 1: Freeze warm water in a cooler for 18 to 24 hours. Then fill the cooler with 4 to 5 inches of warm tap water. Make sure the water is not hot! Place the cooler inside your freezer with the lid off. That’s it!
Does hot water make clear ice?
“Boiling water does not make clear ice. It may make ice a little bit clearer than without, but it makes no significant difference compared to using directional freezing.” There are two methods of directional freezing to try at home—one more involved than the other, but both equally as effective.
How can you make ice freeze faster?
Evaporation – If you use hot water, then it evaporates more quickly so you have less water left over, which can then freeze more quickly.
How do I get ice off my driveway fast?
In a bucket, combine a half-gallon of hot water, about six drops of dish soap, and 1/4 cup of rubbing alcohol. Once you pour the mixture onto your sidewalk or driveway, the snow and ice will begin to bubble up and melt. Just keep a shovel handy to scrape away any leftover pieces of ice.
How do you drive out of an icy driveway?
To completely remove ice from the driveway, use a metal snow shovel to scrape off the slush that remains. If you leave the mostly melted ice on the driveway, there’s a risk of it freezing again. You can also use a big floor squeegee to remove watery slush so that it doesn’t re-freeze into a thin layer of slippery ice.
How do I get thick ice off my gravel driveway?
Hot Water – If the ice is thick and won’t come off, boil a large pot of hot water and apply it to the chunk of ice, making sure to sweep the water off the surface so that it doesn’t get cold and freeze on the driveway. This can be effective to remove ice from the driveway in stubborn areas.
Can you use a regular auger for ice?
We used a earth auger powerhead and a homemade collar to attach a hand auger drill to it for a few years, it worked. That would be my suggestion if you want to use it for ice, find a used hand auger and make an adapter collar so it fits the shaft coming out of the powerhead of the earth auger. It’s an option!
Can you use an ice auger in dirt?
Definitely use a bit for post holes in the ground, the ice auger bit will probably get damaged digging dirt. The different handles on a machine bought to be a post hole digger are more convenient, but you should be able to get by as is.