It would not be accurate to say this is the most important setting, because all of these adjustments need to be accurate for a saw to perform its best, but this is the adjustment that determines how the saw runs in the cut. If you adjust your saw with a dirty air filter, the saw will run too lean when the filter is cleaned. If proper adjustment for your saw is outside the limited range, take your saw into a shop.
If you have a new saw, this won’t apply to you, as new regulations require saws to be built so that only a qualified technician can tune the carburetor. If you have an older saw, here’s how to quickly tune it yourself. Less than five minutes of your time can make a big difference in how well your saw runs.
how to adjust chainsaw idle speed Related Question:
Why is my chainsaw idling high?
The most probable – and easiest to fix – cause of chain rotation while the chainsaw engine idles is a poorly adjusted idle setting on the carburetor. The result is that too much fuel is delivered to the combustion chamber when the throttle is released, and the engine doesn’t really slow.
What are the L and H screws on chainsaw?
The letters on the screws represent High (H), Low (L) and Idle (T). The H screw regulates the Air/Fuel mix during high RPMs, while the L Screw does the same during low RPMs.
How do you adjust H and L screws on a carburetor?
Set the idle speed screw(not L or H) so it is just able to idle by itself. This screw will have a “stop” it rests against. Now turn the L screw out until in decreases in rpm and then back in(very slowly) until it is at peak rpm. Adjust the H screw once more as above and it should be a very serviceable 2 stroke.
What do the high and low screws do on a chainsaw?
Most Pro Saw Engines Have Three Carburetor Adjusting Screws: If this adjustment is set too low, the engine will die when the throttle trigger is released. If this adjustment is set too high, the high idle speed will cause the centrifugal clutch to engage and the chain will run.
Why does my Poulan chainsaw dies when I give it gas?
The carburetor might be clogged. A clogged carburetor is often caused by leaving fuel in the chainsaw for a long period of time. Over time, some of the ingredients in the fuel may evaporate, leaving behind a thicker, stickier substance. This sticky fuel can clog up the carburetor and cause the chainsaw engine to stall.
What are the two adjustment screws on a carburetor?
There should be two screws on the front of the carburetor, which are used to adjust the air and fuel mixture. Often these look like flat-head screws and you can use a screwdriver to turn them, adjusting the amount of fuel and air mixing in the carb.
Why does my chainsaw only runs on choke?
When your chainsaw only runs if the choke is on the problem, in most cases, is a result of fuel supply problems or a faulty carburetor. To fix the problem you should check and clean the fuel system and carburator.
What is the H and L on a carburetor?
They are typically labeled L (low speed jet), H (high speed jet), and I (idler jet).
What is a Stihl 311y?
The MS 311 is a high-tech workhorse with a step up in horsepower and features over the MS 291. With our improved engine technology, you get higher fuel economy for longer run times. The MS 311 also has larger fuel and oil tanks for even longer extended use. You’ll stay productive – while you’re saving money on fuel.
What does H and La mean on a Stihl chainsaw?
One marked “H”, for high speed, one marked “L”, for low speed and one marked “LA”, which is your low speed air adjustment for idle.
How do you adjust the idle on a Stihl 026?
Start the saw and run it to warm it up with the bar and chain on it. With a tach, set the idle to 3300 RPM. Then turn the L screw in or out to get the highest idle speed. Reset the L/A to 3300 RPM again, and redo the process until you get the highest idle from the L screw.
Why does my Husqvarna chainsaw stall?
A clogged carburetor is often caused by leaving fuel in the chainsaw for a long period of time. Over time, some of the ingredients in the fuel may evaporate, leaving behind a thicker, stickier substance. This sticky fuel can clog up the carburetor and cause the chainsaw engine to stall.
How do you use a tachometer on a chainsaw?
Record the engine speed with the tachometer. Look up your chain saw’s maximum safe speed in the operator’s manual. If the tachometer reads more than that speed, turn the “H” screw counterclockwise until the speed falls below the maximum safe speed value.
What RPM does a chainsaw run at?
Depending on your saw, the reading should be between 10,000 and 14,000 rpm. That’s a wide variation, and so it’s important to look up the maximum speed of your saw before conducting this test. The engine should never run faster than the maximum speed at which it is designed to run.
Why does my chainsaw keep bogging down?
The reason for that may be you’re using the saw at altitude or the carburetor adjustment has simply slipped. The saw also won’t operate well at speed if the air filter or spark arrestor or carburetor are dirty.