Chainsaws do not have a blade but a chain made up of lots of little teeth with sharpened blades on them, and few situations are as frustrating as dealing with a length of razor-sharp metal teeth that won’t behave as intended. There is a trick to untangling a new or old chainsaw chain that makes the process so simple that you’ll wonder why you didn’t think of it. Because chainsaw chains are stiff, the dangling, lowest part will poke straight out like a board until it reaches a vertical position.
To survive the situation without postponing the work or destroying the chainsaw, you must learn how to untangle the chainsaw chain. Well, if the chain is still locked up in the chainsaw blade, then you need tools to remove the chain from the chainsaw. If it’s jammed in the chainsaw: Use the tools that suit your chainsaw and open your gasoline or electric chainsaw to get the chain off the chainsaw.
No matter how snarled a chainsaw chain is, you can still untangle it using a simple repeated method. Proper care of a chainsaw and chain will give your chainsaw a longer and more productive life! The easiest way to care for your chainsaw chain is to make sure it’s clean, well-oiled, and the teeth are sharpened.
Now we’ll show you how to untangle a chainsaw chain in the simplest and trendiest way possible. New Chain Case If the chain is new, stay away from honed edges and protect your finger or hand by using uncuttable gloves or chainsaw gloves. If the chain is stuck in the chainsaw, you would have to use the appropriate tools to open your electric or gasoline chainsaw and remove the chain.
how to unfold a chainsaw chain Related Question:
Do chainsaw chains have a master link?
Locate the master link that most manufacturers install to make removal of the chain a simple process. A visual inspection of the chain will reveal the master link due to its appearance that makes it stand out slightly from the other links.
Why is my chainsaw blade smoking?
This most commonly is a result of a dull chain and exerting to much pressure on the bar and chain trying to make the chain saw cut. This could also be either a lack of bar and chain oil ( tank empty, restricted oiler hole ) or an inferior type of oil that is being slung off the chain and not lubricating.
How much slack should a chainsaw chain have?
The chainsaw chain should feel snug but still pull freely. Finally, perform a “snap” test to ensure proper saw chain tension. Simply pull the chain on the underside of the guide bar down so one or two drive links are out of the guide bar rails and release it. The chain should snap directly into position.
Are chainsaw chains directional?
The direction of the chainsaw blade is always the same regardless of the type or model of chainsaw. So the sharp edges of the blade should always face the clockwise direction. If you check from the top, you will notice that the sharp edges are facing the direction opposite the chainsaw body or motor.
Why does my chainsaw chain keep stretching?
A chainsaw chain stretches and loosens from tension and extreme friction. The friction from cutting through wood makes the chain very hot and the heat causes it to loosen. The heat expands the guide bar and when it cools, the chain has stretched. The chain will also loosen as it wears down from use.
Do chainsaw chains stretch over time?
Over time, the chain on your chainsaw will become loose, and new chains will stretch a lot more when you are breaking them in. You need to pay attention so that you can tighten a loose chain before you turn the chainsaw on, as loose chains are dangerous.
Why does my chainsaw blade get dull so fast?
Is the wood that you’re cutting with the chainsaw particularly dirty? Many chainsaw enthusiasts have noted that their blades dull faster when they’re cutting muddy wood. If the logs that you’re cutting up are muddy, then perhaps that is the sole reason why your blade is dulling too fast.
Why is my chainsaw blowing white?
Why is my chainsaw blowing white? While black smoke is caused by the burning of more fuel than air, blue or white smoke is generally caused by the burning of excess oil.
Why does chainsaw cut in a curve?
One major reason a chainsaw curves to either the right or left during a cut is that it was unevenly sharpened. The unequal teeth of the chain cause it to take a different-sized bite into the wood. What is this? The uneven sharpness of the chain is mainly due to manual sharpening, especially with the use of a file.
What is chain master link?
A master link or quick-release link is a roller chain accessory that allows convenient connection and disconnection of a chain without the need for a chain tool. It acts as a set of the chain’s outer plates, so joining two sets of the chain’s inner plate ends.
How often should you replace your chainsaw chain?
The chain sprocket must be replaced if the depth of the wear marks reaches about 0.5mm, i.e. the wear limit. A seriously worn chain sprocket can cause the chainsaw chain and guide bar to wear at an increased rate, as well as reducing cutting performance too, so it’s important to keep an eye on.
How much will a chainsaw chain stretch?
How much will a Chainsaw Chain Stretch? Chainsaw chains stretch considerably after their first run, with about 1/100 of an inch per link. A longer chain with 75 links stretches around 0.75 inch. A shorter chain will still stretch almost half an inch.