We all know the wrestle of getting to replace your chainsaw’s chain right in the midst of a undertaking and trying to figure out the Direction of Chain on Chainsaw. The best technique to exchange or correct a chain on a chainsaw after you’ve taken the machine aside is to start by reattaching the chain bar to the body of the chainsaw. Today I am going to show you how to put on a chain saw chain and the husqvarna chainsaw chain direction.
The most terrible thing which can happen to you is when you put in your chainsaw chain in the wrong direction and begin your task, only for the chainsaw to get blocked in the middle of the project. The direction of the chainsaw blade is always the same regardless of the type or model of chainsaw. “The size of the pitch depends greatly on the type of chainsaw you are using. If your chainsaw is one for heavy duties, then you will have a large pitch. The pitch of a chainsaw is basically the distance between any two repeated chain links divided by 2, that is, the average distance between two successive chain links. So, before purchasing a new chain, make sure it fits the exact pitch so as to avoid ineffectiveness. There are some chainsaw pitches that are most commonly used. They include ¼”, 0.325″, 3/8″, 3/8″ low profile and 0.404″.
Getting the chainsaw chain direction right is very straightforward. In the chainsaw chain direction picture below, the Husqvarna 450 powerhead is on the right and the tip on the left. You can also see the chain direction when looking at the bottom of the bar, facing back toward the powerhead. Hopefully, that makes things clear and you won’t end up with a chainsaw chain on backward!
how to chainsaw chain Related Question:
What part of a chainsaw chain does the cutting?
The cutter is the part of the saw chain that does the cutting. The saw chain has left- and right-hand cutters so that the saw chain will cut evenly through the wood.
What does the gullet do on a chainsaw chain?
The gullet forms the space between the actual tooth and the raker. The depth gauge, or raker, is what prevents the chisel edge of the tooth from biting in too much into the wood. The difference in height between the raker and top plate determines the depth that the tooth cuts with each pass around the bar.
What are the spikes on a chainsaw for?
They are the spikes on the front of the saw, where the blade meets the housing. They are designed to grip into the log or stump in the event that the chain gets bound and the saw kicks back. In short, they are a safety precaution there to stop the saw from jerking back and injuring the operator.
What is a chainsaw tooth?
These teeth are the meat and bones of your chain. They are the cut force of the blade itself and chip away at the wood you are using your chainsaw on. Cutter teeth come in different types too, which are called cutting tooth profiles.
Why does my chainsaw not cut wood?
The most common cause of a chainsaw that won’t cut properly is a dull cutting chain. Try sharpening or replacing the chain. The chain may not have the proper amount of tension. If the adjustment screw is too loose, the chain may not make good contact with the wood.
Why does my chainsaw bar smoke?
This most commonly is a result of a dull chain and exerting to much pressure on the bar and chain trying to make the chain saw cut. This could also be either a lack of bar and chain oil ( tank empty, restricted oiler hole ) or an inferior type of oil that is being slung off the chain and not lubricating.
Why is my chainsaw burning the wood?
Your chainsaw burns wood because of poor lubrication Lubrication allows the mechanical parts to coordinate much better by avoiding a phenomenon of friction which risks causing traces of burns. This is one of the main reasons that your appliance gives off too much heat and that the wood burns.
How do you tell when a chainsaw chain is worn out?
The chainsaw pulls in one direction, which results in a crooked finish. Blunt cutting teeth on one side or uneven teeth lengths usually cause this. The teeth has hit rocks or dirt and broken. If you notice the tops of the teeth are missing you will need to replace the chain.
Why does chainsaw cut in a curve?
One major reason a chainsaw curves to either the right or left during a cut is that it was unevenly sharpened. The unequal teeth of the chain cause it to take a different-sized bite into the wood. What is this? The uneven sharpness of the chain is mainly due to manual sharpening, especially with the use of a file.
How do I know if my chainsaw chain is too loose?
The chainsaw chain should feel snug but still pull freely. Finally, perform a “snap” test to ensure proper saw chain tension. Simply pull the chain on the underside of the guide bar down so one or two drive links are out of the guide bar rails and release it. The chain should snap directly into position.
What is a 60 tooth saw blade used for?
It’s better suited for cutting melamine, chipboard, and plywood. Usually 60 to 80 teeth (on a 10″ blade) with shallower gullets between teeth and a more gentle forward rake around 10°.
What are saw blade gullets?
Gullet size: The gullet is the space in front of each tooth, and its size and depth determine how much wood can be removed during cutting. In general, the fewer teeth a saw blade has, the faster its feed rate and the larger its gullet size.
What are felling dogs?
4-Point professional felling dogs (bumper spikes) for Stihl and Husqvarna chainsaws. These felling dogs are over sized compared to stock to give you better sticking power and leverage in thick barked trees. Pro Safety felling dogs are made of 1/8″ heat treated steel and are sold as a set (inside and outside dogs).
Is more teeth on a chainsaw chain better?
Its cutting edge is more durable that those on either square tooth chain. This can be explained by the fact that the edge on a round cutter tooth is larger and better supported. Square Tooth Round Ground – This chain cuts 10-15% faster than round chain on most saws.
What is the difference between chainsaw chains?
Chainsaw chains come in three main varieties. They come in full chisel, semi chisel and low profile chains, with each being used for different tasks. The chisel refers to how the teeth are cast on the chain itself – which then determines how the chain cuts through the wood.