If the trunk is on a fairly firm surface, you can cut the trunk to length where it is. Making thin trunks, branches and split pieces into firewood. Once you have cut your own logs, they will need to dry for around two years before they can be used on the fire.
First cut should cut should be made from the underside towards the top about 1/3 of the way through the log. Once you had assessed the situation, begin to cut the limbs supporting the tree, cut from under these limbs to avoid the chainsaw getting pinched or stuck. Make an initial cut upwards, about 1/3 of the way through the branch, a short distance from the trunk of the tree so you have room for the final cut which will be close to the trunk.
Some more tips about cutting firewood with a chainsaw. Many chainsaw owners will eventually use their power tools to cut logs for firewood. Cutting firewood with a chainsaw seems easy enough, but it can be quite challenging.
how to chainsaw wood Related Question:
Can you use a chainsaw to cut wood?
Yes, you can use a chainsaw to cut wet wood.
Is it easier to chainsaw wet or dry wood?
No, it is not bad to cut the wet wood with your chainsaw. Dewdrops, raindrops, or the snow on the wood will not cause any harm to your chainsaw. It is, in fact, much easier to cut through the wet wood than dry wood because the extra moisture on the wood will act as a natural lubricant.
What is the most common chainsaw injury?
The most common hazards associated with chainsaws are injuries caused by kickback, pushback, and pull-in. Kickback is the most common and poses the greatest hazard. Kickback occurs when the rotating chain is stopped suddenly by contact with a more solid area throwing the saw rapidly backward toward the operator.
Can I split logs with a chain saw?
For power and efficiency, especially if you have a lot of wood to work with, consider using a chainsaw instead of a hand saw for the job. Chainsaws make it easy to cut trees into logs, and they’ll leave you with enough energy to finish the job. However, don’t just pick the one that looks tough.
How do I stop my chainsaw from pinching?
To stop your chainsaw from getting stuck, make a cut on top of the log or tree that’s preferably one-third of the log’s diameter. Use your chainsaw to cut from the underside until you meet the initial top cut. Always stand on the side when cross-cutting to prevent injury.
What size chainsaw do I need to cut firewood?
Many homeowners find that a 14- to 16-inch chainsaw is a good length for them. That’s long enough to limb-up trees, cut down small trees, and cut most firewood, but it’s also short enough that it’s easy to control the saw.
Can you chainsaw with the grain?
Yes, you can mill a log using a chainsaw, but you need some appropriate attachments. Normally, chainsaws are used to cut across the grain of trees, but it can be adapted in such a way that it cuts efficiently along the grain to mill logs into planks, boards, or beams.
How often should you flip the bar on a chainsaw?
Some professional loggers would advocate that you should flip your chainsaw bar at the end of every use, particularly when you are cleaning up. Others suggest a more relaxed approach advising that you flip the chainsaw bar only when you are changing your chainsaw blade.
Why does my chainsaw get dull so fast?
Dirt Causes A Chainsaw To Dull If you’re cutting through logs and your angle of approach is too steep, a simple cut through could nick dirt or even worse, rocks on the floor causing your chainsaw to jerk, thus dulling.
Is dry wood harder to cut?
Dry Wood Is Typically Easier to Split Regardless of the tree species from which it was harvested, dry wood contains less moisture, so there’s less resistance when cutting and splitting it. An ax or log splitter blade will easily cut through dry wood thanks to its low moisture content.
What should you not do when a tree falls off?
When cutting up a felled tree, avoid touching the ground with the chain because even a brief encounter will severely dull the cutting teeth on your chain saw. If possible, cut partially through the tree and then rotate it to cut the rest of the way through.
How do you cut a log under tension?
A felled tree will usually have saw-pinching areas where the top of the log is under compression and the bottom is under tension. If you have access to the top and bottom of the log, you can handle this one of two ways. Make a cut directly down from the top and then finish by cutting up from the bottom.
Can you drill holes in chainsaw bar?
Re: Drilling a Chainsaw Bar Drilling that bar may not be as difficult as you think. It will be best if you use a drill press, start with a pilot hole, and then drill to the size you need. Make sure you have a sharp bit, run at the lowest speed you can, and use cutting fluid.
How long should chainsaw blade last?
The lifetime of a chainsaw chain has no fixed limit and depends on usage and maintenance. The chain should last many years; 5-6 years should be no problem. However, if the chainsaw chain is used properly and taken care of, it can last way longer.
How do most chainsaw accidents happen?
CHAINSAW ACCIDENTS It occurs when the tip of the guide bar and chain contact an object, forcing the guide bar violently backward and upward. Kickbacks can occur in less than one-tenth of a second, causing severe head, face, neck, shoulder, and hand injuries.