The correct carburetor adjustment will allow the saw to produce maximum power, extend the duty cycle of the engine, produce minimal smoke, idle smoothly, rev up nicely and give trouble free service. High Speed Fuel Adjustment – This is the adjustment that controls the proportion of fuel in the combustible air/fuel mixture at cutting speed. If carburetor adjustment is required due to a new or rebuilt carburetor, it is best to start with the fuel adjustment settings one turn out.
If you have a new saw, this won’t apply to you, as new regulations require saws to be built so that only a qualified technician can tune the carburetor. If you have an older saw, here’s how to quickly tune it yourself. Less than five minutes of your time can make a big difference in how well your saw runs.
how to tune ozito chainsaw Related Question:
What is the H and L on a carburetor?
They are typically labeled L (low speed jet), H (high speed jet), and I (idler jet).
What is the L and H on chainsaw?
The letters on the screws represent High (H), Low (L) and Idle (T). The H screw regulates the Air/Fuel mix during high RPMs, while the L Screw does the same during low RPMs.
Why does my chainsaw not stay running?
Your chainsaw’s engine needs the right supply of air to run properly. A clogged air filter can be the reason why your chainsaw won’t start or stay running. Find your chainsaw’s air filter and remove it. If it’s clogged or too dirty, wash it or replace it.
Why does my chainsaw bog down when I give it gas?
The last thing anyone wants is a saw that purrs when idling and bogs down when applying gas. There are several factors may make your saw not work properly. First, it could be that the carburetor, spark arrestor or the air filter are dirty. Or, the carburetor adjustment might have simply slipped.
What do the H and L screws do on a carburetor?
This adjustment controls the fuel flow to the low speed or idle circuit. If the carburetor is too far out of adjustment to run, or has been disassembled, start with turning the L and H all the way in and then open 2 turns on each needle.
How do I know if my carburetor is rich or lean?
Q: How Do You Tell if a Carburetor Is Rich or Lean? A: One way to tell for sure is by “reading” the spark plugs. If the plug tip is white, the mixture is lean. If it’s brown or black, it’s rich.
How do you adjust a high and low carburetor?
Step 1. Locate the two fuel-adjustment screws on the side of the carburetor. One will be labeled “Hi” and the other “Lo.” The “Hi” screw regulates the engine at full throttle and the “Lo” regulates the fuel when the engine is idling.
Why does my chainsaw stall out when idling?
An engine stalls when it’s getting too much or not enough fuel from the carburetor. Stihl chainsaw carburetors usually have three adjustment screws: one each for idle, low speed and high speed. If the saw stalls while it’s idling, adjusting the idle screw, which usually is marked LA, should help.
Why does my chainsaw spark?
The most common cause of sparks from a chainsaw is metal-on-metal grinding. Whether it’s cutting through wood that has a nail in it or a grinding of gears in the chainsaw housing, a metal-against-metal grinding is the most likely cause.
What does a spark arrestor do on a chainsaw?
The spark arrestor on your chainsaw prevents dangerous hot sparks from igniting fires while you’re working. If the arrestor is clogged or dirty, however, it will also prevent exhaust from leaving the motor, which can prevent it from running.
Why does my chainsaw bog down at full throttle?
If your chainsaw is bogging down when you give it throttle, this is often a sign of improper gas-to-oil ratio. If there is too much gasoline in relation to the amount of oil used, this is known as a “rich mixture” and can cause the chainsaw to run poorly.
Why does my chainsaw rev too high?
The throttle valve (butterfly) simply cuts off the supply of combustible air/fuel and the engine stops. If this adjustment is set too high, the high idle speed will cause the centrifugal clutch to engage and the chain will run. This is a dangerous condition and should never be allowed.
How do you start a stubborn chainsaw?
Try to start the chainsaw after priming the carburetor. 5. Activate the choke by moving the lever to the full choke position and pull the starter rope 3 or 4 times to start the engine. If that doesn’t work, move the choke lever to half choke and pull the starter rope, 6 times maximum, to start the engine.
How do you unclog a chainsaw carburetor?
Let the chainsaw run at low RPMs/idle for a while. This is to let the cleaner run through the carburetor, the fuel lines, and the idle engine. The cleaner will wipe remove the gummy residue blocking the components to create a clean passageway for the air and fuel. As the RPMs begin to increase, turn down the idle knob.