I remember someone on here mentioning using a type of Meguiar’s automotive gel polishing compound; I can’t remember the exact product name, but I remember they also posted some before and after pics of a saw and it looked impressive. This wasn’t all that long ago that I saw this; maybe four weeks at most, but I don’t remember the thread at all.
Master Mech asked that I do a thread about dying the plastic on ugly old Stihl clamshells…So here it goes. There are a ton of old Stihl 1127 and 1123 series saws out there, and they can be brought back to life usually with salvage parts and elbow grease. 2 years ago, there was a claamshell build off at a GTG, so I decided to try and restore an old 039 for it. Parts and a salvaged 029 case, we came to the conclusion there was no way to “NOT” make this thing look like frankenstein. Nothing matched…Well, you can’t paint plastic to any good end, and saws need to be durable… So a buddy of mine mentioned Dying it… So that’s what we did…First we had to scrounge up a metal bucket or drum that could take heat and hold enough liquid to submerge saw parts into. Black…. All the parts had to be run through the parts washer, then cleaned with hot soapy water, to remove the impregnated oil and grease. Then the heat was put to the brew, and we submerged the parts and let em’ boil for 4-6 hours.
how to restore chainsaw plastic Related Question:
How do you restore hardened plastic?
Use soapy water and sandpaper to restore hard plastic. For hard plastics that haven’t been painted, fill a bucket with soap and water. Then, dip 150-grit sandpaper into the soapy water and rub the surface in a circular motion. Cover every faded area 5-6 times.
Can oxidized plastic be restored?
A mixture of five cups of vinegar and one gallon of hot water can be applied via a spray bottle onto the affected area. Long-handled, soft-bristled cleaning brushes help to remove the oxidation. Continuing this manner in small sections works best so the solution does not dry out.
Can you restore sun faded plastic?
If you’ve got white plastic that’s faded to yellow, you can actually restore it with hydrogen peroxide! Tape off or cover any colored areas with some clear tape or masking tape so they’re protected. Use a 12% hydrogen peroxide cream instead of the liquid and brush an even layer over the area.
Does wd40 restore plastic?
No problem. If you’ve got a can of WD-40 Multi-Use Product in the garage, your plastic-cleaning problems are solved. Simply spray onto the area you want to clean and scrub a little with a rag until the plastic surface looks clean. As an added bonus, you can also use WD-40 to polish plastic surfaces on your car.
Does Vaseline restore plastic?
If you have some old, faded electronics or other plastic gadgets in your house, you can make them look great again with just a dab of Vaseline.
How do you soften old brittle plastic?
If you put the plastic, sprue included, into a plastic bag along with a bit of water in the bottom of the bag (the amount is not terribly important — you can experiment), in a couple of days it will absorb a bit of the water and usually will become less brittle.
How do you clean old plastic?
To clean plastic, mix equal parts white vinegar and water in a container. Then, apply the mixture to the plastic and rub it in using a clean cloth or sponge. When you’re finished, rinse the plastic off with water. You can also clean plastic using a paste made out of 3 parts baking soda and 1 part water.
How do you soften plastic permanently?
In general, you can try heating the plastic. How intense the heat needs to be, depends on the type and thickness of the plastic you wish to soften. Plastics will tend to harden again once cooled. Heat (in different forms and methods) are often used to remold or reshape a piece of plastic.
How does heat restore faded plastic?
Heat brings the oils in the plastic up to the surface. It’s temporary and will eventually fade again. A new heat cycle will do it again until there are no oils left in the plastic. IMO Solution Finish is the best way to restore plastic.
How do you make dull plastic shiny?
Using Vaseline And, all you will need is a dab of Vaseline. A petroleum jelly or any ointment which uses a petroleum base can be expertly used to shine dull plastic. You will simply need to rub the jelly onto the plastic, leave it untouched for a minute or so, and then wipe it off.
Can you use rubbing compound on plastic?
After the scratch has been remedied and the surface cleaned, you may notice that the plastic has lost its luster in the working area. To bring back the shine, apply a small amount of either plastic or metal polishing compound, just enough to cover the dull spot, and apply in circular motions with a clean, dry cloth.
What’s the best thing to clean plastic with?
Use a nonabrasive, all-purpose cleaner. Rinse with clean water and dry with a clean, soft cloth. Avoid using abrasive cleanser that may scratch the plastic. Use a tub/tile/sink cleaner; nonabrasive, all-purpose cleaner; or a paste of baking soda and water.
Does heating plastic make it brittle?
Environmental factors such as temperature: Decrease in temperature leads to less mobility and hence more brittle behavior of plastics.
How do you clean dull plastic?
Soak the plastic item in a small bucket filled with vinegar for five minutes. If the cloudiness continues, sprinkle the item liberally with a layer of baking soda and immerse it in the vinegar bath. This should dissolve the film that clings to the plastic and creates that cloud.
Does vinegar harm plastic?
The plastic and glass surfaces on most small kitchen appliances, such as blenders, coffee makers, and toasters, are safe to clean with vinegar, but you want to avoid any rubber parts or metal that vinegar can corrode.