It would be very rare for me to need to cut down a large tree. You can make your initial cuts, let the tree fall, and then cut down the remaining bit to a stump. A few inches above the first horizontal cut and on the opposite side of the tree, make another slice with the chainsaw but don’t cut all the way to the other cut lines.
This page was designed as a quick study guide for the casual user and does not substitute for the owner’s manual or a chainsaw safety class. The Rule of Fives, developed by foresters and professional loggers, reminds the user that there are five stages to safely cutting down a small tree: 1) personal protection, 2) saw safety check, 3) know your surroundings, 4) the felling plan and 5) the stump plan. Get a good night’s rest and eat a healthy breakfast to help you stay alert.
If you want to cut the tree in the opposite direction of it’s lean, or you feel unsure about cutting down the tree by yourself, call a professional. Second, choose a chainsaw that is appropriate for the tree you want to cut down. Don’t try to cut down a large tree with a small chainsaw.
Using a chainsaw to cut down a tree of small height or a leaning tree is quite effective. A tree of small size can be cut down in minutes with a chainsaw whereas it may take several hours [or days] to chop the tree down using axes, saws, or other manual tools. After reading this article, you should have more knowledge about using a chainsaw to cut down small trees and pick out the best chainsaw for small trees.
how to chainsaw small trees Related Question:
What is the best tool to cut down a small tree?
For the typical small tree (less than a six-inch stem), a one-hand bow saw does the trick. It’s also great for sawing up fallen branches for disposal during spring cleanup.
What is the most common chainsaw injury?
The most common hazards associated with chainsaws are injuries caused by kickback, pushback, and pull-in. Kickback is the most common and poses the greatest hazard. Kickback occurs when the rotating chain is stopped suddenly by contact with a more solid area throwing the saw rapidly backward toward the operator.
Can I cut down a small tree with a hand saw?
Trim branches and limbs that will make cutting the tree down easier, or could prove dangerous during your work. Use your handsaw and make a cut on one side of the branch, cutting about a third of the way through. Switch to the other side and continue cutting until the branch falls off.
What kind of saw do you need to cut a tree?
Bow Saw. A bow saw is an all-around great saw for trimming, cutting logs, and pruning. They’re designed to cut on both the pull and the push.
Can I cut a small tree down in my garden?
You will need permission to fell or prune a tree in your garden or land if: It is covered by a tree preservation order – you will require permission from your local authority. It is within a designated conservation area – you are required to notify your local authority to get permission.
Can you drill holes in chainsaw bar?
Re: Drilling a Chainsaw Bar Drilling that bar may not be as difficult as you think. It will be best if you use a drill press, start with a pilot hole, and then drill to the size you need. Make sure you have a sharp bit, run at the lowest speed you can, and use cutting fluid.
Should you flip your chainsaw bar?
Every chainsaw bar has been designed to be mounted right-side up or upside down. The reason for this is that it allows the user to extend the life of his chainsaw bar by 50%. Flipping the bar will give the heavily-used areas some relief from wear and tear.
What is the difference between topping and pollarding?
The major difference between the two words: Whereas the former is done with design in mind, the latter is done out of expediency. More thought and planning goes into pollarding, which is considered an art form, much like topiary. Topping means cutting older trees down almost to the top of the trunk.
Is it OK to cut branches off trees?
Yes, you can kill a tree by over pruning it. It’s best to start small, and only remove a few branches at a time. Then every year, continue working on it until you reach the desired shape. Also, don’t cut off any large limbs unless they are dead or severely damaged.
How do you top a tree with a chainsaw?
Start with a horizontal cut. Place the chainsaw against the side of the tree toward which you want the top to fall. Make a horizontal cut into the tree. Stop cutting when you’re about 1/4 to 1/3 of the way through the tree’s diameter. (In other words, stop cutting well before the chain reaches the center of the trunk.)
How do you cut a tree with a hand saw?
Position the hand saw over the branch as close to the trunk as possible, and begin slicing back and forth, one-third of the way through. Use the entire length of the blade for each cut or stroke through the wood, and work slowly to prevent the blade from sticking or jumping.
Can reciprocating saw cut trees?
Use your reciprocating saw to prune small trees and branches. Reciprocating saws are great for trimming/pruning small trees and branches. Make sure you stick to the safety rules; wear eye protection, have solid footing, etc… Be reasonable about the size of the branch you decide to cut.