Important distinction: bar and chain oil is not the same as the engine oil that is mixed in with chainsaw fuel. The oil outlet port is where the oil from your oil tank leaks out into the oil hole on your chainsaw bar. If you see no oil AND you know your oil tank is full AND you’ve already thoroughly cleaned the oiler, then you have a problem with your oil pump or oil line.
The chain and guide bar oiler on your Stihl chainsaw is an essential component of the saw. It’s simple to check whether or not the oiler works properly: Hold the chainsaw over a flat surface, such as a tree stump, engage the throttle and look for oil drops coming from the spinning chain. The absence of these drops may mean that the oil port is blocked.
Otherwise, you may find the problems like bar oil blockage, bar oil hole clogging. The most common because a chainsaw oiler stops working is that the chainsaw bar oil hole is probably clogged. When oil passes through the bar hole and tries to lubricate the bar’s surface, a dust-up bar groove will obstruct the oil.
how to unclog chainsaw oiler Related Question:
Why is my chainsaw not using oil?
If you don’t see any oil splattering onto the surface of the wood, the chain bar is not sufficiently lubricated. At that point, you will turn off the chainsaw and let the chain brake go. Turning the chainsaw upside down will help you to locate the oiler mechanism. You will see a dial with a minus sign and a plus sign.
How do I clean the oil tank on my chainsaw?
Half fill the tank, close, slosh around, leave sit a while, slosh some more and empty – repeat a few times. Then retrieve the filter line with a hooked wire, change filter, fill with white spirits again and run the saw a while to flush the chanells and pump.
How does a chainsaw bar Oiler work?
But how does a chainsaw oil pump work? The crankshaft drives the pump, which draws oil from the tank and pushes it onto the guide bar via the outlet hole. The movement of the chain then distributes the oil along the entire length of the guide bar.
How do you adjust a chainsaw oiler?
To increase the oil flow, turn the automatic oiler adjustment screw counterclockwise. To decrease oil flow, turn the automatic oiler adjustment screw clockwise. While always wearing heavy work gloves, grasp the chain and pull it towards the nose of the chainsaw to ensure that the chain moves freely.
Can you start a chainsaw without bar oil?
Running a chainsaw without bar oil will cause mechanical problems, and some serious safety issues, such as: Kickback. Chain failure. Dulls the chain.
What happens when the oil pump goes out?
A faulty oil pump will cause oil pressure to decrease to the point where oil can’t flow into the hydraulic lifters of the engine. This will cause the hydraulic lifters to make noise because they aren’t being properly lubricated. As a result, they will wear out quickly.
How much does it cost to change an oil pump?
The average cost for oil pump replacement is between $1,151 and $1,357. Labor costs are estimated between $761 and $960 while parts are priced between $390 and $397. This range does not include taxes and fees, and does not factor in your specific vehicle or unique location. Related repairs may also be needed.
How do you clean a gas tank on a chainsaw?
Replace the lid of the gas tank and shake the chainsaw vigorously. The BBs will act as a mild abrasive and knock any debris loose from inside of the gas tank. Pour the BBs out and flush the gas tank with cleaner. You must ensure all the BBs are out of the tank.
How do you clean the Oiler on a Stihl chainsaw?
Wipe oil and sawdust from the bar, including from the groove in the bar’s rim, by using a rag. Clean the oil feed hole on the bar by poking 16-gauge wire through it. Poke the wire into the oil outlet port on the body of the saw to remove sawdust and dirt that may block it.
How often should I oil my chainsaw?
It is recommended that you grease the bearing in the tip of the bar each time you refuel. Make sure to grease the tip at the end of the day as well to help prevent moisture from entering the bearing as the bar cools.
Where is the oil adjustment on Stihl chainsaw?
Insert a small flat-head screwdriver into the oil adjustment screw on the underside of the chainsaw. Turn the screw clockwise to increase oil flow or counterclockwise to decrease the oil flow, reveals Stihl USA.
Can I use WD40 as chainsaw oil?
No. You should never use WD40 as chain lubricant since WD-40 is NOT a true lubricant. WD40 is primarily a solvent or rust dissolver.
Can I use 2 stroke oil for chainsaw bar oil?
Can You Use 2 Cycle Oil As Bar Oil? You should only use two-cycle oil as the mix, never as a chainsaw bar oil alternative. Using two-cycle oil on the bar will not provide enough tackiness to stick to the chainsaw chain in the summer months. Two-cycle oil also will not work in the winter.
Can I use 10w30 for chainsaw bar oil?
As a matter of fact, you can actually use regular 10w30 motor oil on a chainsaw as one of the alternatives in case you don’t have bar and chain oil. That’s because 10w30 oil has enough thickness and viscosity that will allow it to withstand the friction that is happening whenever you are using a chainsaw.
Do Electric chainsaws need bar oil?
Electric chain saws derive their power from an electric source, so they don’t need fuel to run. Most gas chain saws require a premixed gas-and-oil fuel to operate properly. Electric chain saws don’t require this added oil, but the bar and chain do need to be properly lubricated.