Important distinction: bar and chain oil is not the same as the engine oil that is mixed in with chainsaw fuel. The oil outlet port is where the oil from your oil tank leaks out into the oil hole on your chainsaw bar. If you see no oil AND you know your oil tank is full AND you’ve already thoroughly cleaned the oiler, then you have a problem with your oil pump or oil line.
If the mating surfaces are not clean, oil will drip out and not get onto the bar and chain well. If you don’t clean out the bar rail often, the oil and wood chips and dust will get baked in there and can be very hard to remove, this will make your oil system function poorly. The chain is not picking the oil up because the rails on the bar are worn creating a gap for the oil to go besides being picked up by the drivers.
my chainsaw is not getting bar oil Related Question:
How does a chainsaw bar oiler work?
But how does a chainsaw oil pump work? The crankshaft drives the pump, which draws oil from the tank and pushes it onto the guide bar via the outlet hole. The movement of the chain then distributes the oil along the entire length of the guide bar.
Can you start chainsaw without bar?
It is not recommended to run a chainsaw without a chain. If you need to run it as a movie prop or you are fixing the engine, ensure that you run it for a short time only. I do not recommend letting it run for more than 5 minutes. Without a chain, the chainsaw will cause the engine to rev higher.
Do Electric chainsaws need bar oil?
Electric chain saws derive their power from an electric source, so they don’t need fuel to run. Most gas chain saws require a premixed gas-and-oil fuel to operate properly. Electric chain saws don’t require this added oil, but the bar and chain do need to be properly lubricated.
Do chainsaws always leak bar oil?
In all but very exceptional cases there is nothing wrong with the chainsaw and what appears to be an oil leak is simply oil that has sprayed from the chain as it rotates at high speed, draining from the saw body and guide bar.
Can I use 10w30 for chainsaw bar oil?
As a matter of fact, you can actually use regular 10w30 motor oil on a chainsaw as one of the alternatives in case you don’t have bar and chain oil. That’s because 10w30 oil has enough thickness and viscosity that will allow it to withstand the friction that is happening whenever you are using a chainsaw.
Can I use 5w30 for bar oil?
Can I Use 5w30 for a Chainsaw Bar? Like 10w30 motor oil, you can use 5w30 oil. However, the thin and low-viscosity SAE5 weight oil will not cling to the chain and chainsaw bar very well in the summer. You may experience a lot of oil loss and a messy worksite if you choose this chainsaw bar oil alternative.
What is Auto oiler?
Many homeowner-grade chainsaws use what are known as true automatic oilers, also called fixed flow oilers. As their name suggests, automatic or fixed flow oilers provide a consistent amount of oil whenever the saw is running. Any time you use your saw, you’ll get the same amount of oil on your chain.
Can I use WD40 as chainsaw oil?
No. You should never use WD40 as chain lubricant since WD-40 is NOT a true lubricant. WD40 is primarily a solvent or rust dissolver.
Is chainsaw oil the same as motor oil?
Bar and chain oil is stickier than regular motor oil, so it stays on the chain longer. Motor oil flings off the chain more quickly, so if you try Terry’s tip, be prepared to refill the oil on your chain saw more quickly than with regular bar and chain oil.
What weight is chainsaw bar oil?
What viscosity is chainsaw bar oil? The viscosity of chainsaw bar oil can vary depending on the formula but 30W is standard. In cold weather, a thin 10W chainsaw oil may be advantageous, while very hot temperatures may require a much thicker 40W or 50W formula.
How often should you flip the bar on a chainsaw?
Some professional loggers would advocate that you should flip your chainsaw bar at the end of every use, particularly when you are cleaning up. Others suggest a more relaxed approach advising that you flip the chainsaw bar only when you are changing your chainsaw blade.
How long should a chainsaw bar last?
Re: how long does a bar last The next, a Granberg, lasted about 2 months. About that time Stihl started using them with the same results. A good bar can be filed a few times on both sides and the tip replaced when needed. They could last almost as long as the saw.
Can you drill holes in chainsaw bar?
Re: Drilling a Chainsaw Bar Drilling that bar may not be as difficult as you think. It will be best if you use a drill press, start with a pilot hole, and then drill to the size you need. Make sure you have a sharp bit, run at the lowest speed you can, and use cutting fluid.
Why does my Husqvarna chainsaw leak oil when not in use?
The oil must be of a viscosity that adheres to the chain without being too thick or too thin. If you’ve chosen the wrong oil for the machine, that may be the reason it’s leaking from the bottom. Husqvarna strenuously warns users to never use waste oil in a chain saw.
How much oil should a chainsaw use?
When to Oil Gas chainsaws use about one tank of bar and chain oil for every tank of fuel, so fill the reservoir every time you fill the tank.