This is another common questions from new chainsaw users. Do chainsaws overheat? Yes, chainsaws can overheat but it shouldn’t happen under normal conditions. Here are the most common reasons for an overheating chainsaw. Either way, this is probably the fastest way to overheat and ruin a chainsaw, as it usually happens within 10 minutes of starting it up. Depending on how dull the chain is, this can even cause the chainsaw to overheat due to the huge amount of force it needs to put out all the time. To prevent dust from getting into the engine, chainsaws have an air filter installed. Most chainsaws use the 1:50 oil/fuel ratio, but always check your user manual for the ratio recommended by the manufacturer.
my chainsaw is overheating Related Question:
Why does my chainsaw stop running when it gets hot?
When your chainsaw quits after it gets hot, you either have a problem with gas flow being restricted into the engine or with the spark. This is a common occurrence on older-model chainsaws. By replacing your spark plugs and keeping your gas lines clear you can reduce the chances of this problem recurring.
Is it normal for a chainsaw bar to get hot?
Over regular use, your rakers do decay a lot, and that eventually leads to heat buildup or similar issues on the chainsaw. Eventually, the chainsaw bar can be a passive source of heat buildup from improper raker height. So, the chainsaw raker depth must be accurate in order to reduce any type of overheating.
Why does my chainsaw smoke alot?
This most commonly is a result of a dull chain and exerting to much pressure on the bar and chain trying to make the chain saw cut. This could also be either a lack of bar and chain oil ( tank empty, restricted oiler hole ) or an inferior type of oil that is being slung off the chain and not lubricating.
Why is my chainsaw burning the wood?
Your chainsaw burns wood because of poor lubrication Lubrication allows the mechanical parts to coordinate much better by avoiding a phenomenon of friction which risks causing traces of burns. This is one of the main reasons that your appliance gives off too much heat and that the wood burns.
How do I know if my chainsaw spark plug is bad?
If it’s not producing any sparks at all, your chainsaw needs a new plug. If there are only a few sparks coming out of one side of the electrodes but none on the other side, it’s not bad enough for you to worry about, but it will affect your performance.
Why does my chainsaw chain spark?
The tension not being right is perhaps the most common reason a chainsaw sparks. If the tension is not right, it means that there is too much free moving space between the bar and the chain. When you are running it, the two will collide, and you will notice the sparks spontaneously.
Why is my chainsaw blowing white?
Why is my chainsaw blowing white? While black smoke is caused by the burning of more fuel than air, blue or white smoke is generally caused by the burning of excess oil.
Why does my chainsaw cut on an angle?
Check the size of the top plates, which sit on the longer sections of each tooth on the chain. These top plates should be the same size. If some are shorter than others, file the longer ones down to match. Keep the same angle on all the top plates as you file – angles that don’t match also can cause curved cutting.
When should you throw away a chainsaw chain?
The chainsaw pulls in one direction, which results in a crooked finish. Blunt cutting teeth on one side or uneven teeth lengths usually cause this. The teeth has hit rocks or dirt and broken. If you notice the tops of the teeth are missing you will need to replace the chain.
How often should you replace your chainsaw chain?
The chain sprocket must be replaced if the depth of the wear marks reaches about 0.5mm, i.e. the wear limit. A seriously worn chain sprocket can cause the chainsaw chain and guide bar to wear at an increased rate, as well as reducing cutting performance too, so it’s important to keep an eye on.
Is it worth sharpening a chainsaw?
Sharpening your chainsaw chain is definitely worth it as a sharp chainsaw chain is easier to work with. It takes less effort to cut through wood and your chain will make cleaner cuts with sharp blades. A chainsaw chain can be sharpened multiple times without much of a cost.
How often should you change the spark plug in a chainsaw?
A poorly functioning engine in a Stihl chainsaw can mean more work for the operator and can even be dangerous. Consequently, Stihl recommends replacing the spark plug after every 100 service hours.
Can you clean a spark plug with wd40?
WD-40 removes carbon residue and keeps moisture away from spark plugs and spark plug wires. WD stands for Water Displacement, so if your spark plugs are wet or you need to drive moisture away from ignition distributors, for example, WD-40 is a product you should have handy!
Should the brake be on when starting a chainsaw?
Check the Chain Brake When using a chainsaw, you should always start it with the chain brake engaged so the chain does not move.
How do you start a stubborn chainsaw?
Try to start the chainsaw after priming the carburetor. 5. Activate the choke by moving the lever to the full choke position and pull the starter rope 3 or 4 times to start the engine. If that doesn’t work, move the choke lever to half choke and pull the starter rope, 6 times maximum, to start the engine.