Important: Always make sure the engine is turned off before you begin tensioning the chainsaw chain. Locate the chain tension adjustment points on your chainsaw. Common locations for adjustment points include the side cover and the front of the chainsaw.
There are no formulas or concrete rules on how you should tighten your chainsaw chain. Bar oil is going to be consumed at a higher rate, and if the chain is too tight it can also damage the clutch and bearings when you start the chainsaw. A loose chain will simply flop around the bar grooves, and a chain that is too tight will refuse to budge.
If you are wondering why your chainsaw chain keeps coming loose don’t worry….it’s happened to just about everyone who operates a chainsaw. You can be an expert at tightening your chain but it’s going to be extremely frustrating if you keep having to do so – you need to figure out how to prevent it from coming loose instead. In this article, we’ll tell you everything you need to know about why your chainsaw chain keeps coming loose – and how you can stop it from doing so. Mechanical issues can also be to blame if your chainsaw chain keeps coming loose.
After reading this post, you’ll know how tight a chainsaw chain should be, how to adjust it, and how to test that you’ve got it perfect. If you’re unable to pull the chain away from the bar, then your chain is too tight. If you keep trying to tension your chain and you just can’t get it right, you may have the wrong sized chain.
is a chainsaw chain supposed to be loose Related Question:
How do I know if my chainsaw chain is too loose?
The chainsaw chain should feel snug but still pull freely. Finally, perform a “snap” test to ensure proper saw chain tension. Simply pull the chain on the underside of the guide bar down so one or two drive links are out of the guide bar rails and release it. The chain should snap directly into position.
Why is my chainsaw chain loose?
Chain Not Set Properly One of the most common reasons why your chain might be coming loose is because it was not set properly. When you go through the steps to tension your chain, you need to finish those steps by setting the tension so it won’t change as you work your saw.
Why is my chainsaw chain not tightening?
If you’re having trouble tightening the chainsaw chain, it may be adjusted properly already. Check the tension on the chain by grasping it in the middle of the top of the guide bar and giving it a quick snap. The chain should quickly snap back into place with no sagging on the underside of the guide bar.
How often should you tighten chainsaw chain?
The chain isn’t actually becoming tighter—instead, as you turn the tensioning pin—it pushes the chainsaw bar out a little bit, which takes up the slack on the chain. During a typical afternoon wood-cutting session that lasts 2 to 4 hours, you may need to tighten the chain two or three times.
Can you over tighten a chainsaw chain?
There is a tension screw located near the base of the bar on the chainsaw. To tighten the chain, turn it clockwise, and to loosen turn it counterclockwise. Don’t over-tighten the chain as this could cause it to break.
Why is my chainsaw blade smoking?
This most commonly is a result of a dull chain and exerting to much pressure on the bar and chain trying to make the chain saw cut. This could also be either a lack of bar and chain oil ( tank empty, restricted oiler hole ) or an inferior type of oil that is being slung off the chain and not lubricating.
Why does my chainsaw cut crooked?
Uneven top plates can cause a chain to cut crooked. It’s important to keep all top plates equal length. Dull cutters damaged by rocks can cause a chain to cut crooked. It’s important to remove all damage from cutters prior to cutting.
How long should a chain on a chainsaw last?
The lifetime of a chainsaw chain has no fixed limit and depends on usage and maintenance. The chain should last many years; 5-6 years should be no problem. However, if the chainsaw chain is used properly and taken care of, it can last way longer.
Why does my chainsaw blade go dull so fast?
Is the wood that you’re cutting with the chainsaw particularly dirty? Many chainsaw enthusiasts have noted that their blades dull faster when they’re cutting muddy wood. If the logs that you’re cutting up are muddy, then perhaps that is the sole reason why your blade is dulling too fast.
Why is my chainsaw burning the wood?
Your chainsaw burns wood because of poor lubrication Lubrication allows the mechanical parts to coordinate much better by avoiding a phenomenon of friction which risks causing traces of burns. This is one of the main reasons that your appliance gives off too much heat and that the wood burns.
Can you cut a stump with a chainsaw?
A chainsaw, however, can grind up a stump and leave it all but gone; still, you can’t use a chainsaw to completely grind away a stump. After much of the stump is gone, however, dirt and other material can cover the stump so it won’t be noticed.
What is the best angle for a chainsaw chain?
The sharpening angle will generally be between 25° and 35° – the harder the wood, the greater the angle. To maintain the correct angle, we recommend that you use a sharpening grid or a filing gauge as an aid.
Is it worth sharpening a chainsaw chain?
Sharpening your chainsaw chain is definitely worth it as a sharp chainsaw chain is easier to work with. It takes less effort to cut through wood and your chain will make cleaner cuts with sharp blades. A chainsaw chain can be sharpened multiple times without much of a cost.
How much does it cost to sharpen chainsaw chain?
A typical chainsaw can be sharpened up to 10 times before it’s time for a replacement. The cost to have a chainsaw sharpened ranges from $13 to $16. The average cost per chainsaw sharpening is $14.50 for people who choose to have their chainsaws professionally sharpened.