But how does a chainsaw oil pump work? The crankshaft drives the pump, which draws oil from the tank and pushes it onto the guide bar via the outlet hole. The movement of the chain then distributes the oil along the entire length of the guide bar.
That’s why your chainsaw oiler is so important. The next iteration of chainsaw oiler was still manual, and because it involved an onboard thumb plunger next to the throttle, it eliminated the need for a “Chainsaw caddy.” This advancement in chainsaw oiling technology allowed the operator to manually pump oil onto the bar while cutting. These have proved to be a pretty reliable and effective solution, as the automatic chainsaw oiler has allowed users to adopt a more “Set-it-and-forget-it” approach to keeping their gear lubed up. As more/less all of our modern chainsaw use these automatic oiling systems, let’s look at how they operate. Your chainsaw oiler, in this day and age, probably works off either a fixed flow oiling system or an adjustable flow oiling system. If the chain spits small amounts of oil onto the wood, you’ll know that your chainsaw oiler is functioning properly. As always, if you’ve got any other pro-tips on how to keep your chainsaw oiler functioning properly, feel free to leave them in the comments section below!
Chainsaw oiler consists of an oil pump, oil lines, and oil holes. With the oiler system cleaned from all the debris and gunk, reassemble everything and start your Chainsaw. For electric chainsaw models, you should examine the oiler after each use and make sure it gets replenished when empty.
In this article I’m going to explain why it’s important to keep the chain lubricated and how chainsaw oilers work. With manual oilers you need to release oil onto the chain, usually by pressing a pump button. Some chainsaws come with automatic oilers which allow you to adjust the flow rate of the bar oil.
If your chainsaw is new or you have replaced your chain and guide bar, you will need to keep adjusting the oiler until you determine the right setting that will enable the oiler to produce just the right amount of lubrication. If the above fixes do not work or oiler problems keep recurring, this could indicate that your oiler may be damaged. To ensure that the oiler is functioning correctly, start the chainsaw and let it run for a few minutes then direct the tip of the chainsaw blade towards a piece of wood.
how do chainsaw oiler work Related Question:
Can I use 10w30 for chainsaw bar oil?
As a matter of fact, you can actually use regular 10w30 motor oil on a chainsaw as one of the alternatives in case you don’t have bar and chain oil. That’s because 10w30 oil has enough thickness and viscosity that will allow it to withstand the friction that is happening whenever you are using a chainsaw.
How do you clean a chainsaw oiler?
Wipe oil and sawdust from the bar, including from the groove in the bar’s rim, by using a rag. Clean the oil feed hole on the bar by poking 16-gauge wire through it. Poke the wire into the oil outlet port on the body of the saw to remove sawdust and dirt that may block it.
Can I use 2 stroke oil for chainsaw bar oil?
Can You Use 2 Cycle Oil As Bar Oil? You should only use two-cycle oil as the mix, never as a chainsaw bar oil alternative. Using two-cycle oil on the bar will not provide enough tackiness to stick to the chainsaw chain in the summer months. Two-cycle oil also will not work in the winter.
Can you use transmission fluid for chainsaw bar oil?
On occasion I’ve used tranny fluid to clean out old oil residue in old chainsaws . It works well . In addition to that tranny fluid seems to pump better on some saws with whimpy oilers in cold weather .
Can I use wd40 on chainsaw?
We recommend using WD-40® Specialist® Fast Acting Degreaser and soak it for 10 to 15 minutes. Next, use a wire brush to remove all the grime (repeat several times) and wipe with a paper towel to make sure all the dirt is gone.
What happens when the oil pump goes out?
A bad oil pump will lose the ability to properly pump oil through your system. This will result in low oil pressure that could lead to further vehicle damage. Increased engine operating temperature.
How long do oil pumps last?
You’ll want to check your owner’s manual or the manufacturer’s information online to see how long your particular oil pump should last. Keep in mind that it’s either time or the number of miles, whichever comes first. If you use 12,000 miles per year as a guide, a typical oil pump should last between 5 and 5.84 years.
Why is my chainsaw using so much oil?
What causes a chainsaw to leak oil? As the oil is pumped from the tank through to the guide bar, air begins to replace the space where the oil was previously stored. If there isn’t proper ventilation of the oil tank, a vacuum can occur and reduce the flow of oil to the guide bar.
Can you start a chainsaw without bar oil?
Running a chainsaw without bar oil will cause mechanical problems, and some serious safety issues, such as: Kickback. Chain failure. Dulls the chain.
Why is my Stihl chainsaw leaking chain oil?
This condition is deemed to be normal for any chainsaw with a similar bar & chain lubricating system. If the unit continues to seep oil after a few days, the problem may be the vacuum relief valve located in the side of the engine housing between the oil output hole and the bar stud(s).
Why does my Husqvarna chainsaw leak oil when stored?
The oil must be of a viscosity that adheres to the chain without being too thick or too thin. If you’ve chosen the wrong oil for the machine, that may be the reason it’s leaking from the bottom. Husqvarna strenuously warns users to never use waste oil in a chain saw.
How much oil should a chainsaw use?
When to Oil Gas chainsaws use about one tank of bar and chain oil for every tank of fuel, so fill the reservoir every time you fill the tank.
Is chainsaw oil the same as motor oil?
Bar and chain oil is stickier than regular motor oil, so it stays on the chain longer. Motor oil flings off the chain more quickly, so if you try Terry’s tip, be prepared to refill the oil on your chain saw more quickly than with regular bar and chain oil.