The next iteration of chainsaw oiler was still manual, and because it involved an onboard thumb plunger next to the throttle, it eliminated the need for a “Chainsaw caddy.” This advancement in chainsaw oiling technology allowed the operator to manually pump oil onto the bar while cutting. If the chain spits small amounts of oil onto the wood, you’ll know that your chainsaw oiler is functioning properly. As always, if you’ve got any other pro-tips on how to keep your chainsaw oiler functioning properly, feel free to leave them in the comments section below!
Chainsaw oiler consists of an oil pump, oil lines, and oil holes. With the oiler system cleaned from all the debris and gunk, reassemble everything and start your Chainsaw. For electric chainsaw models, you should examine the oiler after each use and make sure it gets replenished when empty.
The oil system on a Stihl chainsaw lubricates the engine and the bar and chain. The bar and chain oil on a Stihl chainsaw originates from the oil tank on the same side as the gas tank. Stihl chainsaws use an automatic oil pump, which means that whenever the engine reaches a high enough speed to engage the chain, the pump is also activated, taking the hassle out of manually trying to engage the oil pump and control the flow of oil to the bar.
how do chainsaw oil pumps work Related Question:
How do I know if my chainsaw oil pump is bad?
Generally speaking, the signs of a chainsaw oiler problem are easily spotted. If the chainsaw seems like it’s getting too hot or producing smoke, that is a sign that there is an oil deficiency in the chain. This is not good for the life of your chainsaw. If you spot this problem, it is time to troubleshoot the issue.
How does Stihl chainsaw bar oil work?
For a chainsaw engine, the gasoline is mixed with a two-stroke air-cooled engine oil. When the gas reaches the cylinder and gets ignited, the oil-rich fuel will also lubricate the piston and the crankshaft, which allows the piston and the crankcase to receive the proper lubrication to keep moving at high speeds.
How does a chainsaw bar get oil?
The throttle simultaneously engages the motor and the oil pump. As you throttle up, a worm drive engages the pump to send oil through a port that releases onto the bar. As the chain moves across the bar, it distributes the oil across the surface, reducing the friction and the heat that occurs when cutting.
How often do oil pumps fail?
You’ll want to check your owner’s manual or the manufacturer’s information online to see how long your particular oil pump should last. Keep in mind that it’s either time or the number of miles, whichever comes first. If you use 12,000 miles per year as a guide, a typical oil pump should last between 5 and 5.84 years.
Why is my chainsaw using so much oil?
What causes a chainsaw to leak oil? As the oil is pumped from the tank through to the guide bar, air begins to replace the space where the oil was previously stored. If there isn’t proper ventilation of the oil tank, a vacuum can occur and reduce the flow of oil to the guide bar.
How do I clean the oil tank on my Stihl chainsaw?
Half fill the tank, close, slosh around, leave sit a while, slosh some more and empty – repeat a few times. Then retrieve the filter line with a hooked wire, change filter, fill with white spirits again and run the saw a while to flush the chanells and pump.
Can I use 10w30 for chainsaw bar oil?
As a matter of fact, you can actually use regular 10w30 motor oil on a chainsaw as one of the alternatives in case you don’t have bar and chain oil. That’s because 10w30 oil has enough thickness and viscosity that will allow it to withstand the friction that is happening whenever you are using a chainsaw.
Do electric chainsaws need bar oil?
Electric chain saws derive their power from an electric source, so they don’t need fuel to run. Most gas chain saws require a premixed gas-and-oil fuel to operate properly. Electric chain saws don’t require this added oil, but the bar and chain do need to be properly lubricated.
How do you clean a chainsaw oil pump?
Clear any sawdust, congealed lubricant and dirt out of the oil outlet hole on the guide bar. Keep the oil pump tank clean: even if it is equipped with a filter, wipe away all dirt around the cap before refuelling. Regularly check and clean the tank vent and the filter itself.
Can a oil pump get clogged?
How Do I Know If My Oil Pump Is Clogged? An oil filter that is clogged can be one of the causes of poor performance. There is a metallic noise that is audible. The oil pressure is low.
Is it worth replacing oil pump?
Conclusion. You can change oil pump if it starts showing wearing signs. It should last somewhere between 60,000 and 70,000 miles in a properly maintained and regularly serviced vehicle.
What causes oil pump to go out?
If the oil level is too low, the oil pump will have to deal with extra friction due to lack of lubrication. This will cause mechanical problems and warping of various parts in the pump, which will eventually cause the pump to fail.
Where is a oil pump located?
The oil pump in your vehicle is usually located inside the oil pan, which is located on the side of the vehicle. Oil is usually pushed through the engine by a pickup tube that sits on top of the pan. In some engines, it is also located around the crankshaft.
Do all chainsaws leak bar oil?
In all but very exceptional cases there is nothing wrong with the chainsaw and what appears to be an oil leak is simply oil that has sprayed from the chain as it rotates at high speed, draining from the saw body and guide bar.
How often do you oil a chainsaw?
The chain saw should be oiled before each cut. For Manual Oiling System: Lubricate the saw chain by pressing the bulb on the oil reservoir cap twice before making each cut. Hold the bulb down for 3-4 seconds on each press. Automatic oiling system will keep the bar and chain constantly lubricated.