Laminate bars are the right choice for small saws and occasional use or when weight is critical; solid bars should be preferred for long life and repairability in intensive professional use. Laminate bars can be designed to be lighter than solid bars – usually up to around 30% lighter. Affordable entry-level laminate bars may have a solid core plate and weigh essentially the same as a comparable solid bar.
Until yesterday I didn’t know it was possible to make a solid chainsaw bar, laminated seemed so much more logical. Good quality laminated bars are plenty tough and long lasting. Solid bars CAN be heavy…. I have not measured thickness of bars or weighed them on accurate scales but my Carlton German made 16″ Husky bar “Seems” much heavier than my Tsumura on the same saw and in hand…. Bill.
“Back in the day when I felled, limbed and topped for up to 2 skidders I went thru a tip a week. Bearings burn out quick after pinching the tip when topping especially when running a Stihl 064 with 18” b/c. I like to file my chain right down past the witness marks and when the cutters start to break off. Put a few days on a laminated bar and the rails start to spread and they can’t be reliably retighened.
solid vs laminated chainsaw bar Related Question:
Do chainsaw bars make a difference?
Regardless of where they are made, there is a huge difference between the two brands of chain and bars. They use different formulations of steel with different hardness levels. I can tell the difference in the chains just by how they sharpen with a file.
Are Stihl chainsaw bars laminated?
The standard version of the STIHL ROLLOMATIC® Ematic™ bar consists of three electrically welded metal plates (laminated guide bars). A solid and particularly rigid bar with a sprocket nose which can be replaced as a whole.
Are Husqvarna bars laminated?
Laminated bars with nose wheel The gentle curve and small nose radius of these chainsaw bars reduces the risk of kickback and facilitates good cutting control. These bars are coated against scratches and corrosion. Husqvarna offers these bars in 3/8″ Mini .
How often should you change the bar on a chainsaw?
If you are looking for a general idea for how often you should replace a chainsaw bar, a rule of thumb is to replace the bar of your chainsaw once after you have gone through three chains on the same bar.
Can you drill holes in chainsaw bar?
Re: Drilling a Chainsaw Bar Drilling that bar may not be as difficult as you think. It will be best if you use a drill press, start with a pilot hole, and then drill to the size you need. Make sure you have a sharp bit, run at the lowest speed you can, and use cutting fluid.
Can you put an 18 inch bar on a Stihl ms180?
Stihl recommends that its MS 170, MS 171, MS 180, MS 181, MS 192 and MS 211 homeowner models be equipped with guide bars between 12 and 16 inches. The MS 250 and MS 251 models are equipped with larger 45 cc engines and are capable of driving an 18-inch bar.
How long should a chainsaw bar be?
The most common chainsaw bar sizes are 12 to 20 inches, but they come in sizes as large as 72 inches, typically for professionals. The longer the bar, the heavier the chainsaw.
Are chainsaw bars hardened?
The solid chainsaw bar production begins with a solid bar of steel. The machine laser cuts the steel to the desired basic shape. That includes the outer contour, bores, and elongated hole. Looking at the process, the laser makes very little waste in the cut, and Stihl even reclaims the leftover steel.
Why is there a hole in my chainsaw bar?
The hole is part of the manufacturing process when the bar is made at the factory. The milling and heat tempering machines anchor to it and the tail slot. Making a living with a saw since age 16.
Why are some chainsaw bars wider?
The wide belly helps the chain keep from jumping off. Some of those saws are running 16 pins and bigger drivers. The belly in a production bar when running longer bars keeps the chain on the bar better. The chain cuts like a wave going down the bar.
What is the hole in a chainsaw bar for?
These two holes are used to hold the saw blade. if your chainsaw blade not have holes or just have one hole. it not work. if you know how to drill, you can drill two holes on your chainsaw blade.
Can I use an Oregon bar on a Stihl chainsaw?
Chainsaw Bar & S55 Chain, Fits Various Stihl Models (105668) | Oregon Products.
What kind of steel are chainsaw bars made out of?
The steel in most chainsaw bars is high-quality steel that will keep an edge well, but has enough flex to bend under stress rather than break or crack. The metal is generally corrosion resistant, and many bars are a stainless-steel alloy.
Why does my chainsaw chain dull so quickly?
Dirt Causes A Chainsaw To Dull If you’re cutting through logs and your angle of approach is too steep, a simple cut through could nick dirt or even worse, rocks on the floor causing your chainsaw to jerk, thus dulling.
Does cutting wet wood dull a chainsaw?
Does Cutting Wet Wood Dull a Chainsaw? Using your chainsaw to cut through wet wood will not dull the chain any faster than using it for other types of wood. When you think about it, your chainsaw chain is already wet. True, it is not wet with water.