Cut the angle first with the saw at 90 degrees, and then use the off-cut to support the saw while you cut. If you grab your jigsaw whenever there’s a curve to cut, next time try your circular saw instead. It’ll do a sterling job for long, gradual curves in a fraction of the time a jigsaw will. If you’re cutting plywood, set the saw to cut just deep enough to cut through the wood.
Our Recommendation: DEWALT 7 1/4-Inch Circular Saw at The Home Depot for $125.68Dewalt’s 7 1/4-inch circular saw has a low-maintenance sidewinder design with plenty of adjustability, as well as features like onboard wrench storage and a built-in dust blower. Our Recommendation: Skilsaw 7 1/4-inch Worm Drive Circular Saw on Amazon for $199Skilsaw’s 7 1/4-inch worm drive circular saw is the gold standard in worm drives, with plenty of torque, lightweight magnesium parts, and tons of adjustability not found in other models. Our Recommendation: Makita 18V LXT Cordless Circular Saw on Amazon for $179Makita’s XSS03Z 18V LXT compact circular saw weighs just 6 pounds and delivers up to 3,600 rpm, allowing it to handle tough materials with its 5-3/8-inch blade.
how to use electric circular saw Related Question:
What is a circular saw good for?
A circular saw is an essential DIY tool that uses a moving blade to make straight, accurate cuts. While circular saws are traditionally used to cut 2x4s, plywood, and other lumber, they can be outfitted with different blades to cut masonry, metal, and other materials.
How do you use a circular saw without a table?
Fit your circular saw with an edge guide. Set the depth of the blade accurately enough for it to go through the wood and not cut under the surface. Place the guide on base of the circular saw lines and markings you made earlier on the wood. Ensure that the saw is free to move, and the power cord is not entangled.
Which side should the blade be on a circular saw?
For blade-right models, the correct circular saw blade direction is usually with the label side out. For saws that have the blade on the left, it typically installs with the “ugly” side out.
Which way should the teeth face on a circular saw?
The teeth should be cutting UPWARDS, in a clock-wise direction. You’ll also notice that when your blade is installed correctly, the teeth will be pointing upward. Remember: circular saws (as most saws) cut on the upward stroke.
How do you cut a circular saw accurately?
Using a Straightedge for Accurate Circular Saw Cuts Measure the exact distance from the edge of the circular saw’s shoe to the same side of the blade. Once you have that measurement, add it to your original marks and make a new line. Set the straightedge on the new marks, clamp it down, and make your cut.
Can you cut logs with a circular saw?
Circular saws are great for cutting plywood and 2x’s, but you can also cut everything from logs to concrete to steel beams with the right blade or the right type of saw.
Can I use a circular saw instead of a miter saw?
Circular saws do have more versatility than miter saws. Every cut you can make on a miter saw can also be done on a circular saw, plus a few more. This is why my dad (and some others on the internet) recommend starting with a circular saw. But circular saws are tedious to use.
How much power does a circular saw take?
A circular saw typically runs on around 1,200 watts of electrical power.
Why does my circular saw burn the wood?
A dull blade will make it hard to cut quickly, and the slower the feed rate of the saw, the more friction against the wood and the greater the likelihood of scorch marks. Pushing the stock through the saw too slowly is a common cause of saw blade burn. Sometimes a blade that feels dull might only be dirty.
Why does my circular saw kickback at the end of a cut?
Overheating a saw blade can cause it to warp and result in a kickback. Buildup of sap on the blades, insufficient set, dullness and unguided cuts, can all cause an overheated blade and kickback. Never set a blade deeper than is required to cut the work piece 1/8 in. to 1/4 in.
How do you use a circular saw without a sawhorse?
In some cases, it might be better to use your circular saw without a sawhorse. If you need to make cuts without a work support, you can lay a sturdy, stationary surface under the material while making cuts.
What is the difference between a circular saw and a table saw?
Circular saws are lightweight, hand-held, and can be moved from jobsite-to-jobsite with ease. A table saw is heavier and more complex in its set up. Because of its weight and footprint, this tool is more difficult to move these saws around as easily as you are able to do with a circular saw.
Why are so many circular saws left-handed?
The placement of the cordless saw blade, on the left side, gives you a clearer line of sight when you cut. The reason for this is because the main bulk of your circular saw is not blocking your view. Cordless circular left-handed saws provide you better movability.
Do all circular saws rotate the same direction?
Circular Saws This means that the circular saw cuts wood on the upstroke. For a right handed circular saw (most common), this means that the blade rotates counterclockwise, which is similar to the table saw. For a left handed circular saw, the blade rotates clockwise.
Why are most circular saw right blade?
Blade-Right for the Right-Hander Using the saw this way will place the motor weight over the waste edge when you cut from the end-side of a board or sheet. This means the saw eventually cuts off its own support. Most users have no trouble holding the saw steady, but this can result in bind-ups.
