03-02-2009, 6:37 PM #1 Milwaukee Circular Saw Case #6390-21 question As unbelievable as this might seem I got my new Tilt-Lok saw that came in this plastic case and I have no idea how to get the saw back in the case. I should have studied the saw before removing it! It’s made in China, it’s a Chinese puzzle! Place the saw into the case with the handle facing the RH side of the case, the blade facing the back and the motor facing the front of the case.
how to put circular saw back in case Related Question:
Why is my circular saw kicking back?
Overheating a saw blade can cause it to warp and result in a kickback. Buildup of sap on the blades, insufficient set, dullness and unguided cuts, can all cause an overheated blade and kickback. Never set a blade deeper than is required to cut the work piece 1/8 in. to 1/4 in.
Which way does a saw blade spin?
Like miter saws, table saw blades rotate clockwise, meaning the teeth should be pointing down.
What does more teeth on a circular saw blade create?
The number of teeth on the blade helps determine the speed, type and finish of the cut. Blades with fewer teeth cut faster, but those with more teeth create a finer finish.
Why does my circular saw burn the wood?
A dull blade will make it hard to cut quickly, and the slower the feed rate of the saw, the more friction against the wood and the greater the likelihood of scorch marks. Pushing the stock through the saw too slowly is a common cause of saw blade burn. Sometimes a blade that feels dull might only be dirty.
How do you stop a kickback with a circular saw?
Kickback happens when the saw blade binds or stalls suddenly in the wood and the saw gets driven back toward you. So the key to preventing this is to make sure your blade doesn’t bind in the wood.
Can a circular saw blade break?
Making sure your saw blade is working properly is the best way to reduce downtime and increase production. There are many common causes that can cause blade failure from blade selection to cutting speeds, feed rates and improper break-in, to maintenance problems and more.
Does a circular saw need a riving knife?
Riving knives are also fitted to some hand-held electrical circular and powered miter or cross-cut saws (known generically as “chop saws”). As of 2009, Underwriters Laboratories (UL) requires that all new table saw designs include a riving knife.
What can you do to avoid splintering along a cut with a circular saw?
The best option to minimize splintering is to use what is called a zero-clearance insert. Every table saw has a throat plate that sits around the saw blade and it’s main purpose is to support wood, so small pieces of wood don’t go into the hole around the blade.
Why is my circular saw blade loose?
Bearings and washers are mainly responsible for holding a saw’s shaft in place. However, wobbles and misalignments may loosen the blade. This can cause problems while cutting. Moreover, the bolt of the circular saw may wear out after regular use.
Can you put a circular saw blade on backwards?
When cutting vinyl siding with a circular saw, install a fine-toothed blade backwards on the saw for a smoother, cleaner cut, especially in cold weather (when the material is brittle).
Is my circular saw blade on backwards?
When you’re installing your circular saw blade, it’s just a matter of making sure those two arrows match each other. For blade-right models, the correct circular saw blade direction is usually with the label side out. For saws that have the blade on the left, it typically installs with the “ugly” side out.
Do circular saws spin clockwise?
Circular Saws This means that the circular saw cuts wood on the upstroke. For a right handed circular saw (most common), this means that the blade rotates counterclockwise, which is similar to the table saw. For a left handed circular saw, the blade rotates clockwise.
Can I put a metal cutting blade on my circular saw?
Only blades and discs specified for cutting metal should be used. These professional circular saw blades are perfect for cutting through aluminium, copper, lead and other non-ferrous metals; while these diamond cutting discs will make light work of cutting through stainless steel.
How long do circular saw blades last?
They can last between 12 and 120 hours of continuous use, depending on the quality of the blade and material they’re used to cut.
What is a ripping blade for?
The best saw blade for ripping hardwood is a rip blade. This blade is specially made for cutting through wood fibers, so it will cut through hardwood easily and leave a clean edge. Rip blades usually have 10 to 40 flat-topped (FT) teeth, which is a comparatively small number, but it will move through the grain quickly.
