There are several types of saws that you can use to work on laminate flooring. The best saw for laminate flooring would depend on your personal preference and what you are looking to do with it! All of these saws in our guide can cut through a variety of materials while still being versatile in their abilities. Take a look at our recommended saws and read about their benefits to see which saw may be best for you!
The best saw for laminate flooring depends on the type of cuts you want to make. Below are the main features to consider when looking to buy the best saw blade for cutting laminate floors. Due to the tough plastic covering, cutting laminate flooring isn’t as straightforward as cutting hardwood.
The flooring saw is an effective way to cut your laminate boards when installing a floor. If you compare a table saw and miter saw, the former is best for long straight cuts whereas miter saw works best for angular cuts. Following are some of the best blades to cut laminate flooring.
If you want to achieve a professional quality of woodworking, you have to use the best saw blade for laminate flooring, and I will gladly assist you. The laminate flooring saw blade can be used with both table and miter saws that have a standard 5/8″ arbor or a 13/16″ diamond-shaped arbor. In case you are careful enough and know how to treat saw blades, you can buy this 10 inch laminate saw blade even for your first laminate flooring experience.
Although there are a couple dedicated flooring saws that are designed to perform all these cuts, this term can also refer to any type of power or manual saw being used on your flooring. Regardless of the type of flooring saw you use, make sure you’re using the appropriate blade for the material being cut. This dedicated flooring saw blade is designed to provide the features necessary to cover all your flooring needs, including cross, miter, and rip cuts.
best circular saw for laminate flooring Related Question:
What type of saw is best for cutting laminate flooring?
A jigsaw is a real all-rounder when it comes to cutting laminate floors. It’s best used to cut out shapes from your board. For example, when you want to place boards around your toilet or maybe a pillar. Always use a fine toothed blade and have the saw blade spinning before you touch the board.
Can you cut laminate with a circular saw?
To cut through laminate countertops, you can use a hand saw, but a circular saw makes the job much quicker. Because a circular saw can produce jagged edges and chip the laminate, your best bet is to lay the laminate face-side down and cut from the back to the front.
How many teeth blade for laminate flooring?
Diamond-tipped blades that are made for laminate and fiber cement usually have a low number of teeth to reduce the dust produced by cutting cement. However, typical circular and miter saw blades that are used for laminate will have 80 to 100 teeth for fine, precision cutting.
Can you use a circular saw to cut vinyl plank flooring?
Circular saws can and often are used to cut vinyl plank flooring, and if you have this type of saw in your garage or woodshop, it can be used very successfully to cut this material.
Does laminate flooring dull saw blades?
You see, laminate flooring will destroy a wood cutting blade with alternating top bevel (ATB) teeth in no time at all. The sharp points on this type of blade can’t handle anything that hard – they dull quickly and those tips are what the blade uses to cut cleanly through wood.
Can you cut laminate flooring with a utility knife?
Yes. You can cut laminate wood flooring with a utility knife. The utility knife has all the power and cutting capacity to cut through laminate wood flooring whilst not chipping the blade off.
Can I use a table saw to cut vinyl flooring?
Table saws are also great for rip cuts, made with the grain. Since saw blades tend to splinter material as they exit the wood, run laminate flooring planks with the good side facing up.
Can I use a chop saw to cut vinyl flooring?
You can use different types of tools to cut vinyl flooring. Similarly, you can use different types of saw blades to cut vinyl flooring also. For example, you can use a chop saw, a circular saw, or even a table saw to get the job done.
Does Blunt saw blade laminate?
Because of the glue and composite materials in laminate floor boards the cutting edge on normal saw blades will blunt almost instantly.
What size miter saw for laminate flooring?
Working with Laminate Flooring For smaller laminate flooring cuts, you can easily use a 10” miter saw. Switch to a 12” saw if the laminate is on the larger side. Again, this helps maintain precision while also saving valuable time, if you’re on a deadline or simply in a hurry.
Do you need a special blade for cutting laminate flooring?
The main issue when cutting laminate flooring isn’t the type of saw you use but the type of blade. Any saw that cuts wood will cut laminate, but to avoid chipping the hard plastic surface, the blade should have the the maximum number of teeth available.
What tool do you use to cut laminate sheets?
If you only need to make a few cuts, you can get away with using a utility knife and drywall square instead of a saw. Use the same score-and-snap method I used for cutting acrylic sheets. But using a saw is faster and results in a cleaner cut, so that’s the method I used for cutting this laminate sheet to size.
Which saw is used to make curved cuts?
Circular saw technique The first tool that comes to mind for cutting curves is a jigsaw, but if the curve is gradual, try a circular saw instead. It’s surprisingly quick and easy to cut a smooth curve with a circular saw.
Do you cut laminate flooring face up or down?
If you use a jigsaw blade with downward oriented teeth, you should place the boards with the face up. In this manner the saw won’t chip the edges and you will get proper cuts. If you have a blade with upward oriented teeth, you should place the laminate planks with the top-face down.
Do you cut the tongue off the first row of laminate?
Place the first plank with the tongue side towards the wall, being sure to allow 1/8″ for expansion. We recommend cutting off the tongue on this first row to avoid any problem with the expansion gap. Insert the second plank into the first at an angle pressing the short ends together; then press it down.
