No matter the size of your garage, you can enjoy the benefits of plumbing an air compressor setup rather than trying to find a suitable location for your air compressor, snaking your single long air hose around obstacles, and constantly trying not to trip over it. One way to optimize your air compressor plumbing setup could be soundproofing the air compressor by putting it in a cupboard or wooden box! It’s important to ensure the air compressor has proper ventilation so that it has a fresh intake of air and does not overheat. Jimbo’s garage setup has the air compressor situated in the corner of the garage next to a power supply and by the garage door, allowing the first of the outlets to be a 50ft hose reel that permits the use of compressed air outside of the garage.
Compressors with short duty cycles can pose a problem for continuous-use air tools like grinders and sanders, so be sure to get a compressor with a large tank, big motor, and a duty cycle rating of 50 percent or more if you plan to use these sorts of tools. Plumb it UpOnce your compressor is in place, you might be tempted to throw on an air hose with a quick-disconnect fitting and call it “Mission accomplished.” But a good plumbing job is every bit as important as picking the right compressor. That’s all there is to it! With a little planning, a basic air compressor setup will breathe new life into just about any project around the garage.
No matter the size of your shop, you’ll enjoy the benefits of having a piped network of compressed air. Connecting an air compressor to the pipe system with a short, flexible hose lets you disconnect it should you need to take the compressor elsewhere. Quick-connect fittings provide the link between pipe and air hose, below.
Knowing how to set up an air compressor is a fundamental skill for craftsmen to carry out various projects. Connect The Air Hose and Air Tool.The next step is to connect the air hose to your air compressor. So learning how to set up an air compressor in your garage is the initial stage of getting used to it.
air compressor line setup Related Question:
Can you use PVC for air compressor lines?
However, using PVC pipe in any compressed air application is extremely dangerous and NOT recommended by multiple associations and manufacturers. PVC piping is often used to transport liquids, mainly water, for multiple applications.
Can Schedule 40 PVC be used for compressed air?
PVC Pipe. The use of PVC pipe is common but not recommended for use with compressed air. The biggest reason is because it is against OSHA Regulations to utilize PVC and plastic pipes in the United States for compressed air usage.
What size pipe do I need for compressed air lines?
A shear will require anywhere from 8 to 16 cfm at 90 psi through a half-inch pipe. If the pipe exceeds 100 feet in length, you will need a 3/4-inch pipe to accommodate the pressure and velocity of applications that exceed 15 cfm.
Can you use PEX for compressed air lines?
My personal preference for small-shop compressed-air piping is PEX. It’s lightweight and flexible, and the fittings literally snap together. It’s the easiest of any of the options to reconfigure and the simplest to install.
Can PEX tubing be used for air line?
PEX is designed for liquids and shouldn’t be used for air lines. The tubing is “likely” ok, but the fittings are not, AFAIK. There is a similar product out there, however, that is designed for air.
What pipe is best for compressed air?
A great choice for compressed air piping is stainless steel because it is strong and resists corrosion. Like with copper, corrosion resistance in stainless steel piping produces a cleaner, more consistent stream of air.
How far can you run an air compressor line?
Typically, air hoses will be either 50- or 100-feet long, with a few exceptions. Most people will go for the 100-foot option because it allows them to maximize their distance from the air compressor.
What size air line do I need?
The rule of thumb when picking your hose I.D is the higher the CFM requirement of your air tool, the larger the diameter hose you’ll need. Hand held tools such as spray guns and nailers tend to require 1-3 CFM and will work perfectly well with a 6mm hose.
Is Schedule 80 PVC safe for compressed air?
PVC Pipe The use of PVC pipe is common but NOT RECOMMENDED for use with compressed air. It is often used because it is readily available, inexpensive, and easy to install. However, as with many plastics, PVC gets brittle over time and can crack, break, or even shatter.
Can I use SharkBite for compressed air?
SharkBite, part of RWC’s family of brands, now offers a new range of brass push-fit fittings and anodised aluminium pipe to simplify small to large commercial and industrial compressed air installations.
Will increasing pipe size increase flow?
Generally, the larger a pipe is, the higher the water flow. The water pressure level always has to be taken into consideration, however. Even the biggest, smoothest pipes will not have effective water flow if the water pressure is low, because there is not enough strength to defeat the force of friction.
Can I use CPVC for compressed air?
No, PVC and CPVC pipe should not be used for compressed air lines. Here is what the manufacture has to say about it. WARNING! The use of plastic piping with compressed air or gasses can result in severe bodily injury or death.
How much psi can PEX?
PEX-a pipe can withstand a burst pressure of around 800 psi (almost two times the requirement for ASTM F876, the standard specification for PEX tubing). So neither the pipe nor the fittings are weak points, making for an extremely high-performing system in domestic water and hydronic piping applications.
What can I use for air line in shop?
Use copper instead. It’s available at most hardware stores and home centers. Solder it using the same fittings as you would for water supply lines. If you don’t want to solder, use galvanized or black steel pipe.
Is PEX rapid air?
Check out Rapidair, it’s basically the same pex with an aluminum core and designed for the job of handling compressed air. The aluminum core makes the tubing a little stronger but also helps it to retain it’s shape better You can straighten it out or bend curves and it will hold it’s shape so it looks neater.
