Specifically, band saws come equipped with a thin, vertical band saw blade that’s ideal for cutting through thick materials and cutting curves as well. Like any type of saw there are some important tips that should be kept in mind while operating a band saw to avoid accident and injury. And by keeping the rest of these important safety tips in mind, you can safely operate your band saw and ensure a precise, even cut every time as well.
Make sure you understand the instructions before attempting to use any tool or machine. Securely anchor the band saw to the floor to reduce vibration. Refer to Woodworking Machines – General Safety Tips for general safety precautions.
Width: Wider blades are best for thicker wood and straight cuts because they ‘wander’ less than narrow blades. The square steel guide blocks found on many older saws are bad news: They can cause a blade to overheat, and they’ll quickly dull a blade if they come into contact with its teeth. Cut tighter curves, reduce blade vibration and increase blade life by truing the blade with a saw blade finishing stone.
Marvel Vertical Band Saw Safety Rules Do not push the blade into the workpiece hard enough to cause the machine to chatter; slow down and find a more rigid manner in which to clamp the work in the saw. The proper procedure is as follows: firmly clamp the workpiece in the vice; turn on the saw so the blade is rotating; adjust the coolant if necessary; gently bring the moveable saw blade into light contact with the workpiece by rotating the manual feed wheel; engage the automatic feed. Table Saw Safety Rules Special training is required before using the table saw.
band saw do’s and don’ts Related Question:
What should you not do with a bandsaw?
Never push on back of piece with fingers or thumb. Don’t reach across the blade. Make all cuts under power, not while blade is coasting. Never remove guard unless authorized by Technician or WRL Manager.
What must you never do when using the bandsaw to ensure you don’t pull off the blade?
Never attempt to remove the saw from the material or pull it back while the blade is in motion. 19. Always work with a sharp blade.
Can a band saw cut curves?
Whether it’s a tight curve or a closed opening, you can cut it on your band saw with a couple of easy tricks. Cutting on the band saw can be the same thing. The narrower the blade, the tighter the spots you can cut; in fact, some band saw blades rival a scroll saw for cutting tight curves.
When you are finished using the band saw you should?
If it becomes necessary to back out of a long cut, you should: Turn off the motor. Bring the blade to a complete stop and then back the stock out carefully. Force the wood into the blade to get a good cut.
What are the guards on the band saw used for?
Guards. Bandsaws must be guarded. Guarding must prevent access to the bandsaw blade but still allow the employee to see the material being cut. If practicable, employees should use a push stick to guide the work piece through the cutting process.
Do band saws have kickback?
Don’t feed the stock too fast into the band-saw blade. If you do, the blade will chatter, cutting unevenly. (Don’t go too slowly, either, or the blade will tend to burn the workpiece.) There’s essentially no risk of kickback, however, as the motion of the blade tends to drive the work-piece against the worktable.
What is the closest you should put your fingers to the blade while it is running?
Do not put your fingers closer than two inches from the blade. 3. Do not place your hands directly in line with the blade while cutting stock. 4.
What materials can a bandsaw cut?
Most bandsaws have two wheels rotating in the same plane, one of which is powered. The blade itself can come in a variety of sizes and tooth pitch (teeth per inch, or TPI) which enables the machine to be highly versatile and able to cut a wide variety of materials including wood, metal and plastic.
What should you not do with a scroll saw?
Operating Precautions Never wear gloves, a tie, loose clothing, a watch, rings, or jewelry when using a scroll saw. Tie long hair back or secure under a cap. Prior to starting, assure the blade guard is in place and belt guard is closed and tight. Always use the correct saw blade for the cutting task.
What are the hazards of a scroll saw?
►A scroll saw can be hazardous when improperly used. Incidents could include electric shock, fire, or personal injury. ► The following general precautions should be observed by scroll saw users: FIRMLY CLAMP OR BOLT the tool to a workbench or table at approximately hip height.
What are the safety rules for using a pillar drill?
Safety glasses must be worn at all times in work areas. Long and loose hair must be contained. Hearing protection must be worn. Dust mask or other appropriate respiratory protection must be worn Close fitting/protective clothing must be worn.