Logan has some great tips and techniques for turning smaller logs into usable boards using the band saw in your shop. “Making Boards. After cutting the reference faces, you can start making boards. How you plan to use the wood will determine how thick to cut the boards. Keep in mind that the wet, rough-cut boards may warp and shrink. So don’t cut the pieces to the final thickness. Instead, I like to leave some extra material to allow for jointing and planing the wood smooth and flat once it’s dry. Adding about a 1⁄4” is a good rule of thumb. Freshly cut lumber needs to be stored and dried properly to end up as stable boards.
Cutting a log on the bandsaw I had the opportunity to go through some of the pieces of cut up firewood logs at my parents before they were split. If I use a really thin skillsaw blade, the table saw’s kerf will be about as wide as the bandsaw blade’s. In the past, I had no problems cutting though 12 cm thick dried maple with this blade.
George Vondriska provides tips on how to formulate the board foot measure of hardwood so that you can better assess how much wood you’ll need for your woodworking project and better communicate with the salesman when you go to purchase your wood. George Vondriska demonstrates how to use an Epilog laser engraver to cut templates and inlays in your shop. George Vondriska provides tips on how to use a backyard saw mill to cut lumber from logs for your woodworking projects.
I’ve had perfectly acceptable results resawing with bimetal blades and great results resawing with silicone-carbide, low-tension blades. Drift varies from blade to blade, so follow this simple setup procedure every time you change blades. Because bearings can be used in contact with the blade, they can help the blade run straighter, resulting in less drift.
This will keep the log from rolling, rocking, or otherwise moving as it passes through the saw. Depending on the thickness of the log you do this process on your band saw, or move to your table saw. The band saw will slice larger logs and leave a smaller kerf, while the table saw will leave a smoother finish.
band saw for cutting logs Related Question:
How thick of wood can a band saw cut?
Band saws are the undisputed champ when it comes to cutting curves and slicing through thick material. Many small band saws can slice though lumber a full four inches thick, and bigger saws handle six-inch cuts.
How do you cut wooden logs?
To cut your wood slices, we strongly recommend you have either a miter saw or band saw. These are the best saw options to use when cutting log slices, as they can make more precise cuts with the uneven nature of a log. They can also cut thicker pieces of wood than other types of saws.
How much HP does a bandsaw need?
With general cutting of thinner stock with minor resawing, typically a 1-1/2 horsepower motor will do the trick. If you plan on making your own veneer by resawing larger exotic hardwood or cutting bowl blanks from a log, consider looking at units with a 2-1/2 to 3 horsepower motor.
How thick can a 9 inch bandsaw cut?
There are several $99, 9 inch band saws on the market in my area (Ryobi, Skill). The are able to cut a thickness of 2 ½ inches.
How many teeth does a bandsaw blade have?
The general rule of thumb is: For wood and soft materials aim for 3 – 6 teeth in the workpiece. For metals and harder materials aim for 6 – 24 teeth in the workpiece.
Can you rip a 2×4 with band saw?
A band saw can shape curves, saw rough lumber safely, cut joinery, and even rip boards to width. The last item on this list is often met with skepticism. After all, most woodworking plans mention using a table saw for ripping boards. On top of that, band saws have the reputation of only being useful for rough cutting.
Will a bandsaw cut 2×4?
your “small” tablesaw is one of the finest in the portable table saw category and should have no problems resawing a 2×4 although you may want to finish the cut with a jig saw by setting the blade slightly less than half the thickness of the 2×4.
How do I stop my log slices from splitting?
If your wooden slice was cut and left to dry for longer than a few days, use wood sealer as a soaking solution to help prevent cracks or splits from forming. Fill the container just over halfway so you can submerge the wooden slice without overflowing the container.