On a typical wood or metal cutting blade the hook or of point of the blade should be pointing down for a vertical blade bandsaw, or for a horizontal blade saw the hook of the teeth should be pointed such that they enter the workpiece first as the blade moves. During regular cutting on a well set up bandsaw the blade will move or bow backwards a bit as you press the workpiece into it. The side guides will assist in keeping the blade cutting straight, but they are not an iron lock on the blade forcing it to cut straight.
This in turn causes the blade to not cut in a straight line. With a dull blade, there is an expectation for it to cut slower and cut crooked. The main thing that normally goes out is the crown, which is what is holding the blade in place, Most of the time the blade is right at the center, but if the crown begins to wear out, it may start allowing more and more movement, causing the blade to not cut in a straight line.
If the blade twists and the work piece is harder to push through the cutting area, replace the blade. Loose blade tension can also cause the blade to twist and veer off course when cutting the work piece. Check blade tension by pressing in on the side of the blade using a gloved finger.
Then the blade starts to heat up with the extra friction. Sometimes you can remove the blade and completely clean it and it will cut again for a little while, but usually the heat build up has dulled the teeth and the blade is dead. I know you want to use a fine tooth blade for the boxes so you have less sanding. You may want to try a blade that has a combination tooth pattern, maybe an 8-12 pattern.
Being a happy bandsaw owner has a lot to do with your approach to coping with the fact that a bandsaw simply will not cut straight, or, in the sage words of veteran woodworkers, “Adjusting for drift.” Even the top performing 14″ bandsaw on the market, Powermatic’s 14 Bandsaw 1791216K, comes with a no-frills fence with 4 bolts on top rather than easy and obvious thumbscrews or knobs that say, “Adjust me here!”. Making the bandsaw cut nice and straight with this fence is a snap.
band saw not cutting Related Question:
Why is my band saw not cutting?
Band Saw: Why won’t my band saw cut straight? When the band saw cuts crooked, a dull blade, improper feeding, loose blade tension or not using a work piece guide could be the cause. Use the rip fence or miter gauge to guide the work piece uniformly through the cutting blade to make straight cuts.
Why is my bandsaw blade stopping?
Using a dull blade or the incorrect type of blade can cause the band saw to cut through work pieces slowly. The blade will also move slowly through the work piece if the blade is installed incorrectly. A weak drive motor can also cause the band saw to cut slowly. First, check the installation of the band saw blade.
Why won’t my bandsaw cut metal?
Band saws are not suitable for cutting very thin sheet metal; a rule of thumb suggests the metal to be cut should be thicker than the depth of 3 band saw blade teeth, however they are excellent for cutting thin walled profiles such as box and angle.
Why is my horizontal band saw not cutting straight?
Make sure the blade is running in the correct direction. On machines powered by three phases power so it is common to get the wiring reversed and have the blade running the wrong direction. On all vertical blade bandsaws the working portion of the blade should go down. This forces the workpiece down into the table.
How do you straighten a band saw blade?
How to straighten a bandsaw blade? It is risky but if it’s absolutely necessary, a temporary fix to straighten a bandsaw blade can be done by placing it on an anvil and gently tapping it flat with a nylon head hammer/mallet or using a pair of gas pliers to straighten out the blade.
How much tension should a bandsaw blade be?
For carbon steel toothed blades (cutting blades) this is typically 15,000 to 25,000 PSI. Slitting type blades typically are tensioned in the range of 12,000 to 20,000 PSI. In general bandsaw blades are never tensioned past 35,000 psi.
What causes bandsaw drift?
Drift is cause because the blade buckles under the load. You can see that by stretching a ribbon between 2 points and applying a pressure to one of the edges, it will turn sideway easily. A sharp blade and high blade speed will help a lot with that.
Why does my bandsaw mill blade wander?
When you’re sawing a soft wood with hard knots, the engine will slow down each time you hit a knot. If the blade speed drops below about 5000 FPM, the blade will start to wander. The governor will kick in to get the engine back up to speed but by the time that happens you’re through the knot.
Can a bandsaw cut hardened steel?
Carbide band saw blades provide high wear resistance and toughness when cutting a variety of applications such as: case hardened steels, spring steels, high speed steels, nickel based alloys, case hardened steels, composite graphite, high nickel alloys, titanium, inconnel, and other exotic metals.
How long should a metal bandsaw blade last?
On average your bandsaw blade should last 6 months to as long as a few years depending on what your cutting with it. Make sure to match your blade strength and quality to the project and material your cutting.