On a typical wood or metal cutting blade the hook or of point of the blade should be pointing down for a vertical blade bandsaw, or for a horizontal blade saw the hook of the teeth should be pointed such that they enter the workpiece first as the blade moves. During regular cutting on a well set up bandsaw the blade will move or bow backwards a bit as you press the workpiece into it. The side guides will assist in keeping the blade cutting straight, but they are not an iron lock on the blade forcing it to cut straight.
05-21-2018, 11:08 PM #1 Horizontal Bandsaw Not Cutting Square I just got this older 4×6 Busy Bee B013 horizontal bandsaw and it’s not quite cutting how it should. 05-22-2018, 11:24 AM #2. 05-22-2018, 12:01 PM #3 I just got this older 4×6 Busy Bee B013 horizontal bandsaw and it’s not quite cutting how it should. 05-22-2018, 12:49 PM #5 Most likely explanation is insufficient blade tension, assuming a good blade.
The original question of the saw not cutting square vertically is due to the fact that the blade cuts in the direction its pointing. What has been missed so far is that if the arm doesn’t fall square to the vice table, the blade, even if adjusted as above, it will still not cut square vertically. To know if you’ve got this problem, using 6″ engineers square like in the photo above, place it so the blade of the set square just touches the tip of one of the teeth that is set toward the vice and clamp it up hard.
Rotate the blade so the tooth is now at the back of the table and move the miter gauge/stick assembly to the back and see if it touches the marked tooth to the same extent. The blade does not move directly around the center so you will need to repeatedly go back to the front of the blade, readjust the screw, and then again measure the back. Slide the miter gauge to the front of the table and move the fence over to the screw head and insert a playing card between the screw head and the fence just so you can move the card as it touches both the fence and the screw head. Now move the miter gauge to the back of the table and see if you have the same feel when you insert the card.
Being a happy bandsaw owner has a lot to do with your approach to coping with the fact that a bandsaw simply will not cut straight, or, in the sage words of veteran woodworkers, “Adjusting for drift.” Even the top performing 14″ bandsaw on the market, Powermatic’s 14 Bandsaw 1791216K, comes with a no-frills fence with 4 bolts on top rather than easy and obvious thumbscrews or knobs that say, “Adjust me here!”. Making the bandsaw cut nice and straight with this fence is a snap.
band saw not square Related Question:
Why is my band saw not cutting straight?
Band Saw: Why won’t my band saw cut straight? When the band saw cuts crooked, a dull blade, improper feeding, loose blade tension or not using a work piece guide could be the cause. Use the rip fence or miter gauge to guide the work piece uniformly through the cutting blade to make straight cuts.
Why is my band saw cutting at an angle?
A bandsaw has a spring that you tighten to keep the blade under tension. Your saw will probably have instructions for how tight to make the blade. This spring can loose its ability to properly tension the blade after some time, allowing the blade to twist in the cut.
How do you straighten a band saw blade?
How to straighten a bandsaw blade? It is risky but if it’s absolutely necessary, a temporary fix to straighten a bandsaw blade can be done by placing it on an anvil and gently tapping it flat with a nylon head hammer/mallet or using a pair of gas pliers to straighten out the blade.
How tight should metal bandsaw blade be?
The blade should deflect no more than 1/4 in. A good place to begin is to tension the blade until the meter reads proper tension for the next wider blade. For example, if you’re tensioning a 3/8-in.
Should bandsaw blade twist?
Typical bandsaw blades can be flipped “inside out” to make the teeth point the other direction. On some knife edge style blades and grit edge blades you can get a fresh sharp cutting edge from a blade this way, just by flipping it inside out.
Can a band saw cut curves?
Whether it’s a tight curve or a closed opening, you can cut it on your band saw with a couple of easy tricks. Cutting on the band saw can be the same thing. The narrower the blade, the tighter the spots you can cut; in fact, some band saw blades rival a scroll saw for cutting tight curves.
What makes a circular saw cut crooked?
What Causes a Circular Saw to Not Cut Straight. A faulty circular saw is likely to have issues such as an unstable blade or a warped blade edge. The problem could also be the way you operate the saw. If you do not operate the circular saw properly, it will not cut straight.