Was enjoying ideas I see in many threads and thought I’d share acouple I have. Couldn’t find a thread these would fit in so started a new……. “Bench top drill press is bolted to 3/4″ plywood topped toolbox, box is full of drill bits etc… and very heavy/sturdy. I modified a HF bandsaw and put a better quality blade/switch, 12” disc mounted on old motor, belt driven grinder/wire wheel still in work.
When autocomplete results are available use up and down arrows to review and enter to select. Touch device users, explore by touch or with swipe gestures. 3y.Collection by Similar ideas popular now.
Broke blades regularly, it was only the fine blade model, bloody racket Bunnings were charging $30 a pop for blades. If you go to a 6mm blade you may be OK. The scroll saws are good and blades are only $2 a pop. My bandsaw is a carbotech its absolutelely brilliant i think it cost me around $450 a year ago but as yet has’nt broken a blade and its done a fair bit of work.
Try smoothing rough, curved edges using a belt sander that has one side perpendicular to the platen. Turn on the belt sander and press the workpiece against it until you sand the edge down to the line, as shown above. Spray-adhere 80-grit through 120-grit sandpaper to the curved scraps, and work the edges down to the marked lines.
bandsaw and disc sander Related Question:
Can you sand with a bandsaw?
Now you have a belt sander that can sand parts as tall as your bandsaw capacity. There are a number of advantages to working this way: Burning is reduced because the belt has time to cool as it travels around the wheels. The 1/2” wide belt allows for easily sanding outside and even shallow inside curves.
What should you not do with a disc sander?
NEVER wear gloves or hold the work with a rag when sanding. SAND with the grain of the wood. DO NOT sand pieces of material that are too small to be safely supported. AVOID awkward hand positions where a sudden slip could cause a hand to move into the sanding belt or disc.
What is a band saw sander?
A band saw is basically a “curve cutting” machine. It is not capable of doing inside cutting. For inside cutting use our Dewalt 20 inch Scroll Saw. The Craftsman Band Saw-Sander is not only capable of the usual band saw operations, but it can he converted into a sander as well.
What is a disc sander best used for?
Disc sanders are benchtop sanders with a circular sanding disc attached to a circular plate mainly for shaping wood pieces. They are commonly used for fine-tuned finishes, smoothing end grain, straight cuts, miter cuts, sanding curved edges, sanding curves or bevels and any kind of shaping necessary.
Why do you sand only on the downward spinning side of the disc?
Sand on the downward side of a disc sander so that the wood is driven onto the table by the machine’s rotation. Enclose all drums, disk or belt sanding machines with an exhaust dust hood that covers all portions of the machine but the portion designed for the work feed.
Is it safe to sand on either side of the disc sander?
ALWAYS sand on the downward side of the disc (Left side) when using the disc portion of the machine. Sanding on the upward side of the disc could cause the work piece to fly up which could be dangerous.
Should you wear gloves when using a belt sander?
Never wear gloves when using a belt sander. Many work gloves do not always fit tightly. This creates a situation where the gloves can actually become caught in the sander. You should always wear protection for your ears when using any type of power tool.
How long is a 12 inch bandsaw blade?
The Craftsman 12″ Bandsaw-Sander takes an 80″ blade or an 80″, 1/2″ wide sanding belt.
What size blade does my bandsaw take?
Use coarse tooth blades (2 or 3 TPI) for re-sawing and cutting thicker materials. For general wood cutting duties in typical 3/4″ material, use a 4 TPI blade for coarse, fast cutting and a 14 TPI blade for slower, smoother cutting. A blade in the 6 to 8 TPI range provides good general-purpose performance.
What is the difference between a belt sander and a disc sander?
With a long straight surface, belt sanders can be vertical, horizontal or can have the option of both. Popular for the trade workshops, the belt sander is much bigger in size than the bobbin and disc sander. Its long flat surface makes it ideal for flattening and levelling long pieces of timber such as panelled doors.
What is a 12 inch disc sander used for?
These benchtop beasts bring both muscle and finesse to sanding chores. When you need to quickly and precisely sand outside curves, or fine-tune miters and crosscuts, nothing beats a dedicated 12″ disc sander. Its table accepts a miter gauge to deftly sand precise angles for joinery.
What is the difference between an orbital sander and a disc sander?
Disc Sander While random orbital sanders are all disc sanders, not all disc sanders have random orbital motion capability. Some disc sanders have non-orbital sanding faces that spin in a fixed motion. These sanders are best for rougher work where a lot of material needs removal before moving on to a finer surface.
What are the 3 most important sander safety rules?
Safety Rules Dust mask advised. Don’t wear loose clothing or gloves, keep long hair tied back. Never adjust Sander or setup while Sander is running. Never remove guard unless authorized by Technician or WRL Manager • Setups requiring anything other than the standard sander equipment must be approved by supervisor.
When using a belt sander you should never?
What should you avoid while working with belt senders? Do not use a sander without an exhaust system or a dust collector present that is in good working order. Empty the collector when 1/4 full. The dust created when sanding can be a fire and explosion hazard.
How long should you use a sander for?
But – random orbital sanders are designed to be used extremely slowly. Not quite a snail’s pace, but perhaps an ant’s. So, what’s the ideal speed? About ten to twelve seconds per linear foot.