If you’ve ever tried to resaw using a fence to guide the board, you know that the blade can sometimes drift, leav-ing you with an uneven cut. It’s better to steer the board with a resaw guide that makes contact with the wood at a single point. To use the resaw guide, first lay out the cut on the workpiece.
Re-sawing a board into thin, pliable pieces allows you to create curved shapes by bending and gluing the pieces around a form-a process called “Bent lamination.” Marking the board with the cabinetmaker’s triangle allows you to reassemble the thin pieces as they came from the board, so the lamination closely resembles a single piece of bent wood. Partially re-sawing a board on your table saw makes re-sawing with your band saw easier, because the blade has less to cut and the saw kerfs keep it from wandering. It’s a great method to use if your band saw bogs down during full-width re-sawing, and in many cases, it can save time by allowing you to re-saw without installing a re-saw blade.
To get started with resawing, I recommend a band saw of sufficient power and with a large depth of cut. “And, speaking of saw blades: the rule of thumb for resawing is “The wider the better.” Wider blades, 1/2″ and larger, cut straighter, which is the goal. Even if you don’t opt for a “specialty” resaw blade, stick with a wide and open-toothed blade to enhance your resawing activity.
“The Fence. The fence is simple. Use 1/2″ plywood for the base, face, and brace. Use 3/4″ hardwood for the contact point. The height of the face should be close to the width of the material you”ll be resawing. A few downsides to resawing on a bandsaw with a single point fence;. If you’re resawing pieces to various sizes you’ll need to move and reclamp the fence for each cut.
20) Bandsaw log sled and resaw fence for any bandsaw.
bandsaw resawing guide plan Related Question:
What size bandsaw do I need for resawing?
To get started with resawing, I recommend a band saw of sufficient power and with a large depth of cut. Any motor smaller than 1hp and depth of cut less than 10″ will limit your effectiveness. (Some 14″ band saws have about a 6″ maximum cutso you’d be limited to a 12″ wide book-matched panel or less.)
What bandsaw blade is best for resawing?
Resawing involves making rip cuts in the face of a wide board. So just like you would on the table saw, you’ll want to select a blade with fewer teeth per inch (TPI) than the blades you use for crosscutting or cutting curves. For most 14″ band saws, a 1 ⁄ 2 “-wide blade with 2-3 TPI is a good choice.
Can any bandsaw resaw?
Just about any bandsaw will do acceptable resawing. For example, all the cuts made in this story were done on an inexpensive, 14-in. bandsaw with a 3/4-hp motor. All we did to the saw was add a riser block to increase its capacity.
What is a resaw guide?
Resaw guides provide a higher level of control when adjusting for band saw blade drift. Curved face of the guide helps steer board into the cut. Easily attaches to the face of the band saw fence. This 7″ Resaw Guide is designed for larger capacity band saws.
How much horsepower do you need to resaw?
A 3/4 or 1 HP bandsaw is pefectly adequate for re-sawing stock at home….
Can I put a wider blade on my bandsaw?
An 18-inch diameter wheel can use a 0.032-inch thick blade that is 3/4 inch wide. In general, thicker and wider blades will be the choice when sawing dense wood and woods with hard knots. Such wood needs the extra strength of a thicker, wide blade to avoid breaking. Thicker blades also deflect less when resawing.
What does the fence do on a band saw?
Never before has a band saw fence allowed you to accomplish such a wide variety of cuts. This fence adjusts both for blade drift and perpendicularity to the blade (essential when cutting thin veneers).
How many teeth do you need to resaw a blade?
Typically, a wide 3-tooth-per-inch (tpi) blade provides the perfect blend of aggressive yet smooth cut and sawdust evacuation that resawing requires.
How thick can a bandsaw cut?
Band saws are the undisputed champ when it comes to cutting curves and slicing through thick material. Many small band saws can slice though lumber a full four inches thick, and bigger saws handle six-inch cuts.
Why does my bandsaw burn the wood?
A majority of issues with wood burning is because of a dull saw blade. These blades may not be sharp enough to efficiently cut the wood, and thus create enough friction to heat and burn the wood. What is this? Dull blades make it more challenging to cut, which causes friction as you pass the wood through.
Can you resaw with a table saw?
When it’s time to resaw lumber for thin stock, a bandsaw usually comes to mind. But in many situations, such as preparing 1⁄ 4 “-thick stock for a project, you can do it on your tablesaw. Most 10″ tablesaws easily resaw boards up to 5 1⁄ 2 ” wide.
What is the best TPI for cutting wood?
If you’re looking to cut wood or other soft materials, you’ll need a blade with a TPI of 6 up to 20. For harder materials like metal, a TPI between 14 up to 36 is more suitable. The number of teeth can be found on the blade.
Why do bandsaws wander?
If the wheels are worn and do not have a distinct top to the crown then the blade will not know where to go, and may wander around. This of course can cause poor cut quality and difficulty in setting the guides.