I’ve been resawing lottsa walnut veneers for my Tansu project. Even with all this, I start off with S4S, slice a veneer, plane, slice a veneer, plane, slice a veneer, plane…. I cut all my veneers to 3/32″ and then drum sand down to 1/16″. The sanding part is slow, mind-numbing work but I’ve gotten excellent results from this procedure. If you need to veneer only one side of a panel, it may not be so critical what the glue side looks like.
A bandsaw will make many cuts with precision and speed-when equipped with the right blade for the application. Bandsaw blades differ in thickness, width, length, and tooth configuration. Every time you change from one bandsaw blade width to another, you have to reset the saw’s tracking, tension, and blade guides.
It is 20hp, 1 1/4″ 2 tooth blade, pretty good cut, fairly fast with hydraulic feed works, but even though you could glue directly off the saw it isn’t good enough for a finished line. From contributor C: I think the Woodslicer blade is a good blade for smaller machines – I’ve tried it for my needs, trying to slice 12′ boards, and it doesn’t work. I’ve run 1,000s of bd ft with a single blade and the cut is as good as a Woodslicer.
Premium blades have hardened teeth, and they far outlast ordinary blades. We tested all the premium resaw blades we could find that can safely be used on a 14-in. If you do a lot of resawing, you may find bi-metal blades worth the extra money because the extra-hard teeth are designed to outlast hardened carbon-steel blades.
For resawing, the width of the blade should be close to the maximum the bandsaw will handle. On one forum, one person had great results with the Laguna Resaw King, but another person’s Resaw King blade broke, and Laguna said it was his fault for excess tension, even though they had refused to specify the recommended tension. Most bandsaw gauges don’t specify what thickness blade they are calibrated for, which is why they may be perfect for one blade, but are often misleading for other blades.
best bandsaw blade for cutting veneer Related Question:
What kind of band saw blade should I use?
Use coarse tooth blades (2 or 3 TPI) for re-sawing and cutting thicker materials. For general wood cutting duties in typical 3/4″ material, use a 4 TPI blade for coarse, fast cutting and a 14 TPI blade for slower, smoother cutting. A blade in the 6 to 8 TPI range provides good general-purpose performance.
Is more teeth on a saw blade better?
The number of teeth on the blade helps determine the speed, type and finish of the cut. Blades with fewer teeth cut faster, but those with more teeth create a finer finish.
Is a wider bandsaw blade better?
The wider blades are stiffer overall (more metal) and tend to track better on the band wheels than narrow blades. When cutting thicker material, the wider blade has less ability to deviate because the back end, when in the cut, helps steer the front of the blade, especially if the side clearance is not excessive.
Is more TPI better?
Woodworkers quickly learn that the number of teeth-per-inch (TPI) on the blade has a big impact on the quality of a cut. The general rule of thumb is “the more TPI, the smoother the cut.” The true answer, however, is just a little more complicated than that, as you’ll learn once you understand how saw teeth work.
Do I need a scratch coat for veneer stone?
Step 3: Scratch Coat A scratch coat will be needed when metal lath is used. This step is not necessary when applying stone veneer to a cleaned concrete, masonry, or stucco surface.
What is ATB saw blade?
Alternate Top Bevel (ATB) This means that the blade teeth alternate between a right- and left-hand bevel. This configuration yields a smoother cut when crosscutting natural woods and veneered plywood.
How do you prevent Tearouts when routing?
To avoid tear-out, cut the piece oversize, rout the curved edge, and then rout the piece to final size. When using a template to create a workpiece, cut away the waste material as close to the cutline as possible.