1 – The bandsaw blade length is specific to each model bandsaw. Watch where the bandsaw blade is contained and slowly free it from each section of the bandsaw. When the blade is up to speed, I feed in the left edge of the green wood bowl blank and begin following the edge of the cardboard circle, without cutting the cardboard.
Currently running a Timberwolf 3/4 wide blade with 2 teeth per inch. The blade I am running now has cut about 70 green bowl blanks and still cuts good. Does a great job, just make sure you watch your fingers.
05-31-2009, 10:46 PM #1 Best bandsaw blade for bowl blanks Hello everyone, I have a Jet bandsaw that uses 133″ blades. 06-08-2009, 3:34 PM #14 saw blade I have a Jet 20″ and have also used Timberwolf & Olson blades. 06-08-2009, 3:48 PM #15 I bought a 2 tpi AS 1/2″ blade from my local saw sharpening service which seems to work just fine for bowl blanks.
As a bowl turner I like to do most of my bowl preparation with some jigs I made for my bandsaw that will take a 2′ or 3′ log and I can use it to cut it down the center of the pith or cut it on each side of the pith so there is no pith in my bowl blanks, I usually will put on an 1″ or 1-1/4″ bandsaw blade and spend the day ripping my logs in half. I experimented with 3/8″, 1/2″ 5/8″ bandsaw blades for cutting bowl blanks. If I could find some good bandsaw blades I wanted to negotiate a discounted price for anyone who might need one or two from both our facebook group, Wood Turning Basics https://www.
Process logs into useable turning blanks, cut pen blanks to size, cut corners off a bowl blank… the uses of a band saw are too many to list. We have shop tested all the band saws and accessories we carry so you can buy with confidence.
I was using it for resaw stuff down to pen blank size. He took my Griz apart, re-did everything and it still wouldn’t track or cut. He said the saw was great, set up just right, just a POC blade.
best bandsaw for cutting bowl blanks Related Question:
What size band saw for blank bowls?
While a 17” bandsaw can easily handle a bowl blank that is eight inches tall and 16 or 18” in diameter, a 14” bandsaw may only have a cutting depth of five or six inches. With a six-inch cutting depth, or height, a 14” bandsaw cannot handle blanks taller than six inches.
How do you seal wood to turn blanks?
Once the wood has been air dried and cut to the final size I usually seal the end grain with wax. Canning wax, Candle wax, Paraffin wax, any type of wax that turns to liquid when heated will work fine for sealing wood blanks.
What are turning blanks used for?
What is this? A wood turner uses wood turning blanks to turn a number of parts or finished products. A wood turning blank can be shaped into any object that is cylindrical or round in essence. A skilled operator however can create a large array of objects with their block of wood.
Is more TPI better?
Woodworkers quickly learn that the number of teeth-per-inch (TPI) on the blade has a big impact on the quality of a cut. The general rule of thumb is “the more TPI, the smoother the cut.” The true answer, however, is just a little more complicated than that, as you’ll learn once you understand how saw teeth work.
How many band saw teeth should contact the workpiece at once?
TPI is measured from gullet to gullet, not tooth tip to tooth tip – this is known as pitch. The general rule of thumb is: For wood and soft materials aim for 3 – 6 teeth in the workpiece. For metals and harder materials aim for 6 – 24 teeth in the workpiece.
How long should a metal bandsaw blade last?
On average your bandsaw blade should last 6 months to as long as a few years depending on what your cutting with it. Make sure to match your blade strength and quality to the project and material your cutting.
Can a band saw cut curves?
Whether it’s a tight curve or a closed opening, you can cut it on your band saw with a couple of easy tricks. Cutting on the band saw can be the same thing. The narrower the blade, the tighter the spots you can cut; in fact, some band saw blades rival a scroll saw for cutting tight curves.
What is the throat on a band saw?
The throat is the distance from the blade to the vertical frame section of the body of the saw. This distance determines the width of cut that can be completed on the band saw. The throat on a free-standing cabinet band saw typically exceeds the 12 to 14-inch throat of smaller, bench-top models.
Are band saws useful?
A band saw can be used to cut curves, even in thick lumber, such as in creating cabriole legs, to rip lumber and to crosscut short pieces. The most common use for the band saw, however, is in cutting irregular shapes. The second most common use is in resawing or ripping lumber into thinner slabs.