Chainsaw bar oil is a necessary component to operating your chainsaw at peak efficiency and with safety in mind. Formula Chainsaw bar oils are either petroleum-based or bio-based. ‘ Chainsaw bar oil for winter is usually 10W. Very hot temperatures may call for a thicker chainsaw oil, in the 40W to 50W range.
best chainsaw bar oil australia Related Question:
What oil is best for chainsaw chain?
Rapeseed-based (usually called canola) oil is currently the most common environmentally compatible chain-and-bar lubricant. Vegetable-based oils are triglycerides or natural esters that come from agricultural crops.
What kind of oil do you use for bar and chain on a chainsaw?
If your manufacturer’s bar and chain oil is unavailable, you can use SAE 30 weight motor oil to lube your chain during the summer and SAE 10 weight during the winter, according to the University of Missouri Extension.
Are all chainsaw bar oils the same?
What viscosity is chainsaw bar oil? The viscosity of chainsaw bar oil can vary depending on the formula but 30W is standard. In cold weather, a thin 10W chainsaw oil may be advantageous, while very hot temperatures may require a much thicker 40W or 50W formula.
Can I use any 2 stroke oil in my chainsaw?
Can I use any 2 stroke oil in my chainsaw? No, you can’t use any 2-stroke oil in your chainsaw. Some 2-stroke oils are built for motor oils, and this might damage your chainsaw. Also, 2-stroke oils for an air-cooled engine are different from a water-cooled engine.
Can I use 10w30 for chainsaw bar oil?
As a matter of fact, you can actually use regular 10w30 motor oil on a chainsaw as one of the alternatives in case you don’t have bar and chain oil. That’s because 10w30 oil has enough thickness and viscosity that will allow it to withstand the friction that is happening whenever you are using a chainsaw.
What does 10w30 mean?
The 10W30 designation on engine oil means that the viscosity of the oil is rated at 10W when an engine is cold, and 30 when the engine is hot. This is different than an oil labelled 5W30, which has a thinner viscosity when the engine is cold at 5W.
Can I use 5w 20 for chainsaw bar oil?
They are 5w20 and 10w30, which would be best? You can but it’s not very good for the chain or the environment. The Husqvarna / Stihl stuff is much thicker and vegetable based so it doesn’t fling off the chain as easily or poison your garden!
Can you use old motor oil for chainsaw bar?
Some people caution against using motor oil on a chain saw, but not for safety reasons or concerns about equipment. Bar and chain oil is stickier than regular motor oil, so it stays on the chain longer.
Can I use gear oil as bar oil?
Unless you are using your chainsaw in hot conditions, gear oil is not a recommended alternative bar oil.
Do battery chainsaws use bar oil?
Due to the constant metal-on-metal friction between the bar and chain of a chainsaw, the bar needs to be continually lubricated with oil. This allows the chain to run smoothly. Without it, chains break easily. Look for a rechargeable chainsaw with an automatic bar oiler, which will constantly apply oil to the bar.
Do Electric chainsaws need bar oil?
Electric chain saws derive their power from an electric source, so they don’t need fuel to run. Most gas chain saws require a premixed gas-and-oil fuel to operate properly. Electric chain saws don’t require this added oil, but the bar and chain do need to be properly lubricated.
Is synthetic two-stroke oil better?
Synthetic two-stroke oil is better for the environment, producing lower deposits and emissions due to lower ash content. Petroleum-based two-stroke oils include non-lubricant solvents and additives that allow for easier gasoline mixing. These solvents and additives burn at a high clip and produce higher emissions.
Do you mix oil with gas for chainsaw?
Most STIHL gasoline-powered equipment runs on a 50:1 mixture of gasoline and 2-cycle engine oil. Knowing the proper way to mix your fuel is the first step in keeping it running strong and long.
What is the best fuel for a chainsaw?
Use a minimum of 89 octane gasoline and always use fresh fuel. Only buy enough gasoline that you can easily use up within a two- month period. For air-cooled, two-cycle engines, use a quality mix oil that meets the engine manufacturer’s recommendations.
Can you use transmission fluid for chainsaw bar oil?
On occasion I’ve used tranny fluid to clean out old oil residue in old chainsaws . It works well . In addition to that tranny fluid seems to pump better on some saws with whimpy oilers in cold weather .