Malco’s Vinyl Cutting Circular Saw blades come in three different models, VCB1, VCB2EV, and VCB3EV. VCB1 – VERSATILE 7-1/4 INCH CIRCULAR SAW BLADE IS A MUST-HAVE FOR PORTABLE CIRCULAR SAWS. A popular blade choice when you need to go where the work is. Why settle for a make-do plywood blade when you can have the real thing in a flat-ground 186 tooth blade that offers smooth cutting in a range of vinyl plastics including vinyl fencing, siding and trim profiles. The large 10″ diameter provides a deeper, more efficient blade path for fast cuts in wide siding panels and more accurate single pass cuts in large profile vinyl fence posts.
best circular saw blade for vinyl siding Related Question:
What is the best blade to cut vinyl siding?
How to cut vinyl siding is a question asked by many homeowners. For vinyl shake siding, you can cut panels using snips or a circular saw with a blade that can be used for vinyl. Snips work best for long, vertical cuts while circular vinyl siding saws work best for short, vertical cuts.
Can you cut vinyl siding with a circular saw?
If you need to cut a lot of vinyl strips and you’re making short, vertical cuts, the quickest and cleanest way to work is with a circular saw. If you’re only cutting a few strips of vinyl and making vertical cuts, using a pair of tin snips is simplest.
What kind of blade Do I need to cut siding?
A fine-tooth plywood saw blade will give you the best results when cutting vinyl siding with a circular saw. Avoid using other kinds of saw blades or you may not get a clean cut. You can find a fine-tooth plywood saw blade online or at your local home improvement store.
How many teeth do I need to cut vinyl siding?
A 36 TPI rating, which means 36 teeth per inch, will be adequate for the job. A jigsaw will allow you to cut corners and right angles when fitting the siding around doors, windows and other protrusions along the house. Cutting with a jigsaw may leave rough edges, but they can be smoothed out with 220-grit sandpaper.
Why do you need to leave a ¼ expansion joint when installing vinyl siding?
Allow for Expansion and Contraction Vinyl siding installation must allow for material expansion and contraction caused by weather. Cut your siding in lengths with a 1/4-inch gap for expansion wherever siding butts accessories.
How do you cut siding on a circular saw?
Fit your circular saw with a fine-toothed plywood-cutting blade (installed backwards for the cleanest cuts). Put on your safety goggles, then line up the place you want to cut on your siding with your blade. Use the edge of your table as a guide and slowly saw off the excess siding.
Do I need house wrap behind vinyl siding?
There is no logical reason not to have house wrap under vinyl siding, and many authorities strongly agree that it should be viewed as mandatory, even if your local building codes don’t necessarily require it. Vinyl siding is one of, if not the most popular exterior cladding for residential homes.
What temperature does vinyl siding brittle?
Cold Weather Chilly weather makes installation frustrating because the colder it gets, the easier the vinyl will crack. Putting in the siding in temperatures lower than 40 degrees increases chances for cracking and buckling.
What temperature should vinyl siding be installed?
Vinyl, the most popularly used siding in the country is actually quite sensitive to any extreme changes in temperature. In cold temperatures, it shrinks down, and when it heats up it expands. The ideal temperature to install vinyl siding is around 50 degrees which makes spring and fall the perfect time.
Can you hang vinyl siding in the winter?
A typical 12′ long piece of vinyl siding will expand over 5/8″ from winter to summer. Now that you know vinyl siding will get longer and shorter with changes in temperature you can deal with this issue appropriately as you install it. Ideally you’ll install vinyl siding when the temperature is around 50 degrees F.
Can I use screws for vinyl siding?
Use aluminum, galvanized steel, or other corrosion-resistant nails, staples, or screws when installing vinyl siding. Aluminum trim pieces require aluminum or stainless steel fasteners. All fasteners must be able to penetrate a minimum of 1 1/4” (32mm) into nailable material, such as wood sheathing and framing (Fig.
Does siding need to be nailed into studs?
Siding must be secured into metal studs if the substrate is not a nailable surface such as exterior dry wall, gypsum board, etc.
What goes under siding on a house?
Underlayment Underlayment or weather resistive barrier (WRB) is installed between the siding and the sheathing. This can be tar paper or a house wrap such as HardieWrap® or Tyvek HomeWrap®. HardieWrap® is great for keeping water out and at the same time letting water vapor escape from the house.
