Preferably use a circular saw with a PVC blade or a sharp and straight fine-tooth carbide blade. If your saw blade is designed for rough cutting lumber and dull, it could shatter the vinyl.
Preferably use a circular saw with a PVC blade or a sharp and straight fine-tooth carbide blade. If your saw blade is designed for rough cutting lumber and dull, it could shatter the vinyl.
Malco’s Vinyl Cutting Circular Saw blades come in three different models, VCB1, VCB2EV, and VCB3EV. VCB1 – VERSATILE 7-1/4 INCH CIRCULAR SAW BLADE IS A MUST-HAVE FOR PORTABLE CIRCULAR SAWS. A popular blade choice when you need to go where the work is. Why settle for a make-do plywood blade when you can have the real thing in a flat-ground 186 tooth blade that offers smooth cutting in a range of vinyl plastics including vinyl fencing, siding and trim profiles. The large 10″ diameter provides a deeper, more efficient blade path for fast cuts in wide siding panels and more accurate single pass cuts in large profile vinyl fence posts.
This review is only for cutting ABS U-channel with 0.050″ wall thickness. After bumping the saw see the rotation, I saw that the blade was warped – about 3mm of wobble! These two observations indicate substandard QC.Nevertheless, I tried a few cuts on my channel and there was substantial melting of the plastic. So this blade is no good for my use, and because of the warp, its going back.
This blade is inexpensive and works well for cutting vinyl siding. You will notice the teeth on the blade are backwards from a normal wood blade. The kerf if this blade is very thin which makes the blade wobble slightly.
best circular saw blade to cut vinyl Related Question:
Can a circular saw cut vinyl?
Hand-Held Circular Saw: Most circular saws are able to get the job done when it comes to cutting vinyl siding as long as they are fitted with a fine-toothed blade.
How many teeth do you need to cut vinyl?
Use one that has between 80 and 100 teeth to make smooth, fine cuts. Circular saws can produce the same type of cut as a miter saw because they use a similar cutting blade. This high tooth count blade by DeWalt makes smooth cuts and slides through vinyl quickly to keep from melting.
Can you cut a vinyl fence post with a circular saw?
Measure the length of the fence panel you want to cut and mark using a carpenter’s pencil or chalk. Be sure the mark is straight and square. Using a circular saw with a fine-tooth blade, cut the vinyl fence along the mark you created in step two.
What is the best tool for cutting vinyl siding?
If you need to cut a lot of vinyl strips and you’re making short, vertical cuts, the quickest and cleanest way to work is with a circular saw. If you’re only cutting a few strips of vinyl and making vertical cuts, using a pair of tin snips is simplest.
Can you cut siding with a circular saw?
Fit your circular saw with a fine-toothed plywood-cutting blade (installed backwards for the cleanest cuts). Put on your safety goggles, then line up the place you want to cut on your siding with your blade. Use the edge of your table as a guide and slowly saw off the excess siding.
Can you use a chop saw to cut vinyl siding?
These include miter saws, chop saws, table saws and handheld circular saws. Mark the area to cut and slowly feed the blade into the siding. The backward rotation of the saw blade not only cuts the vinyl, but melts the edges to make a very smooth and jagged-edge free cut.
What is a 40 tooth saw blade used for?
Deep gullets provide good chip removal. Crosscut blades, made for cutting across the woodgrain (across the face of a board), have between 40 and 80 teeth and are designed for clean cuts. Smaller gullets separate the teeth. Combination blades can make both rip cuts and crosscuts.
What is a 60 tooth saw blade used for?
A crosscut blade, on the other hand, is designed to produce a smooth cut across the grain of the wood, without splintering or tearing. This type of blade will usually have 60 to 80 teeth, and the higher tooth count means that each tooth has to remove less material.
What does more teeth on a saw blade mean?
The number of teeth varies depending on numerous factors, including application, so you’ll have to determine whether you’ll be using the blade for ripping or crosscutting. Ripping, or cutting with the wood grain, requires a blade with fewer teeth than crosscutting, which involves cutting across the grain.
What blade should I use to cut vinyl?
Vinyl fencing can be cut just like wood. Preferably use a circular saw with a PVC blade or a sharp and straight fine-tooth carbide blade. If your saw blade is designed for rough cutting lumber and dull, it could shatter the vinyl.
Can I cut vinyl plank with table saw?
It cuts just like wood or MDF. I just installed a vinyl plank floor and I was able to do cross cuts by snapping and scoring, cut around door jams using a jigsaw and rip it to length on the table saw.
Do you need a special blade to cut vinyl with Cricut?
What blade do you use to cut vinyl on Cricut? To cut vinyl with ease, we recommend the premium fine point blade and a green mat. Once your design is created and you are ready to cut, we do recommend choosing “more pressure” when cutting vinyl.
Why didn’t my Cricut cut my vinyl?
Ensure you are using a Cricut brand blade. Inspect the blade and blade housing and remove any debris that may be stuck to the blade or lodged in the blade housing. Once clean, perform a test cut. If the blade and housing are already free from debris, or cleaning it did not help, proceed to step 3.
Can an angle grinder cut vinyl siding?
In fact, grinders can cut through the vinyl almost as quickly as a miter saw but a grinder is much smaller and more portable. You’re still tied to an outlet, but at least you can easily move it when you need to.
How do you cut vinyl on a table saw?
When using your table saw to cut vinyl planks, you will need to change the blade in the table saw to a fine-tooth blade. Blades that have a low tooth per inch (TPI) count will generally make a rougher cut than blades that have a higher TPI count.
