1/4 inch to 1 3/16 inch 23 Gauge Pin Nailer with a low profile nose piece for a clear view.
For Depth Control and Longer Life, there is a switch that can be adjusted.
Heavy-duty aluminum housing that is easy to move aroun.
It comes with a nailer, 1/4-inch Air Fitting with Oil and a Nail Selection Tool, a Carrying Case, and a Belt Hook.
An overview of what this item is abou.
Collation Type: Adhesive; Fastener Range: 1/2 in. to 1-3/16 in., 23 Gauge; CFM per Shot: 0.018; Required Pressure: 70 to 100 psi; Max Pressure: 100 psi; Magazine Capacity: 200; Rear Exhaust: Rear Exhaust; No-Mar Tip. The housing is made of aluminum in a yellow color. When you buy this tool, it comes with (500) 1/2-inch, (500) 3/4-inch, and (500) 1-1/4-inch pins, as well as the tool itself and a case to keep it in when not in use. It’s 2.50 pounds.
Amazon.co.
The Bostitch HP118K 23-Gauge 1/2-Inch to 1-3/16-Inch Headless Pin Nailer gives you the precision and comfort you need to finish, trim, and work on wood projects quickly. This pin nailer gives you the power of pneumatic action backed by Bostitch’s long history of making fastening tools that work well on the job.
The fastening is strong and can be adjusted for precise, clean work.
An 18-gauge nail or brad could split materials that aren’t thick enough for a Bostitch HP118K to work with. A 23-gauge pin nail set and this tool can help you avoid damage to work surfaces. The HP118K is a good choice for woodworking because it can be used to fasten glue sets that are hard or impossible to clamp, and it can help you avoid the marks or holes that other driver heads can leave behind.
This nailer was made to keep you in control at all times. It has a high/low power control that lets you set pin depths without having to change your compressor setting. Precision: It can drive 60 in./lbs. of force, so you can be sure that each pin is in the right place.
This nailer can handle 23-gauge headless pin nails that range in length from 1/2 inch to 1-3/16 inches. This allows you to use a wide range of fasteners for different jobs. And it has a magazine capacity of 200 pins, so you don’t have to stop to reload.
Ergonomic Design for Comfort and Eas.
The HP118K has a wide range of design features that make it easy and safe to use. It has a low-profile nosepiece that goes down to the contact point, giving you a clear line of sight for perfect placement. An over-molded grip makes it easy to use, and it is balanced to stay in your hand for a long time. For extra comfort while you work, the nailer’s rear exhaust moves air away from your face while you work. The pin nailer also has a belt hook that can be turned around for easier use on the job.
Its small size makes it easy to move around, which is important when you’re working on things like custom cabinetry or picture frames. Because it has a durable, lightweight aluminum housing, it only weighs 2.5 pounds.
A Pneumatic Performance That Is Reliabl.
This lightweight and durable tool can operate between 70 and 120 PSI. It comes with a 1/4-inch NPT fitting that makes it easy to connect to your air hose and compressor.
This pin nailer comes with a manufacturer’s 7-year limited warranty. This tool is very easy to use.
How to Put the HP118K in.
1. Press the spring-loaded lever as shown in the loading instructions below.
2. Pull the sliding part of the magazine back as shown in the loading instructions Fig.2.
3: Load the stick of pins in the way shown below in the loading instructions Fig.3. Make sure the arrow pattern is going down as shown. Black dots instead of arrows should be on the top of pins.
It is shown in loading instructions Fig.4 how to do this: 4. Close the magazine as shown below until it latches forward. The tool can now be used.
What’s inside the box.
Pin Nailer: HP118K 23-Gauge Pin Nailer; 1/4-inch air fitting; 500 pins; tool lubricant; tool case; and lubricant for the nails.
Loading Instructions and Bostitch Fasteners You Can Find.
It’s easy to carry, cheap, and works well. It makes me sad, though, that it has so many problems with pins that are 1 inches long. Go ahead and hold the nose to the surface. The pin will stand out from the material you’re trying to pin if you hold it close to the surface, like this. Jack up the pressure that comes in. There’s no way. Is it possible to go up. Still, I’m very happy. It makes me think there’s a design flaw inside of it that just won’t let it sink pins fully. I’m not sad that we’re no longer together, but I’m glad it helped me figure out what I needed in a (Grex) pin nailer.
