“After starting a hole in the ice with your spud, you must switch to your chainsaw and angle its blade as you cut. To cut a straight line in the ice, you should keep the blade of your chainsaw at a forty-five degree to a sixty degrees angle, not straight upward and downward, and make the cuts in ice as you push its blade into the ice, not while you draw it backward,” Thompson said. The lessons learned over the years with my chainsaw include; before shutting the chainsaw off, I always walk a distance away from the group of my students and rev the chainsaw up to clear any water, then it is shut off and place up off the ice. “My chainsaw is more than thirty years old and, now I am using it on ice only. It looks and runs like a brand new one. Check the length of the board, its appropriate distance, and then use the chainsaw to cut another hole in the ice ahead of the board. If you notice sawdust on the ice, you should stop immediately as the board is being cut, so you should quickly move further away.”
When you running your saw on the ice for the first time of the season, do a bunch of cutting before you get to your spot. That will flush and clean out your “Ice saw” so when you actually get to your spot you hole is nice and clean with no oil slick…. I screw in a T ice anchor before cutting as an aid to lift the block up and out before cutting… Make your cuts at a slight angle so your block can only come out one way. Ever since I bought my ice saw I have never needed the chainsaw for cutting a spear hole.
Consider the ice thickness and the safety of using a chainsaw to prevent any injuries or falling into the ice if it were too thin. You can go for specialized ice-cutting tools such as ice augers, which are used for cutting circulation holes in the ice. Once you have cut through the ice, use an ice bar or pick when extracting larger ice out.
can i use my chainsaw to cut ice Related Question:
What should you not do with a chainsaw?
Don’t Cut With a Dull Blade Cutting with a sharp blade actually extends the life of your chain saw. That’s because a sharp blade pulls itself into the wood, while a dull blade requires lots of downward pressure. That pressure wears out the bar, drive links, clutch sprocket and clutch.
Can you cut frozen wood with a chainsaw?
It’s not impossible to cut frozen wood with a chainsaw, but it is extremely difficult. Cutting wood requires a sharp chain and frozen wood will dull your chain.
Can you cut in the water with a chainsaw?
No, you can not run a chainsaw in the water. You can work in the rain and wetlands, but you cannot submerge a regular chainsaw underwater to cut anything under the water surface. If you submerge a gas-powered chainsaw underwater, the water will get into the engine and ruin your chainsaw.
How do you cut ice?
“Ice fishing can be kept simple,” says Thielen. “You need a good six-inch hand auger like a Strikemaster Lazer auger, until the ice hits eight inches thick.” Thielen repeated the need to drill down as straight as possible. “It’s much easier to cut through when drilling straight,” he said.
Should you run a chainsaw at full throttle?
Engine Protection Generally, two-stroke chainsaw engines are built to conveniently run at full throttle without an engine breakdown. Therefore, running at any throttle speed below the full throttle is not advised.
What happens if you run a chainsaw without bar oil?
Without lubricant, the speed at which the chain moves over the chainsaw bar can cause some serious friction. A slowed-down chain and excessive fuel burning mean there’s a lot of friction between your bar and chain, which means a lot of heat is being produced that could do major damage to your saw.
Is wood harder to cut when frozen?
Frozen wood cuts a lot harder than non-frozen wood. Hard maple is the worst, but red oak and hickory aren’t much better.
Is it OK to use a chainsaw on wet wood?
Can you cut wet wood with a chainsaw? Yes, you can cut the wet wood with a chainsaw. Besides, there is a misconception that wet wood can impact the chainsaw bar and chain. But actually, the damp wood will not dull the chainsaw any faster than using it on other types of wood.
Can you saw frozen logs?
The most difficult time to saw logs is when they are partially frozen because the blade cuts in and out of the frozen material. Sawing partially frozen logs can be done successfully, but will generally require a little slower feed speed in order to monitor each cut.
How often should you flip the bar on a chainsaw?
Some professional loggers would advocate that you should flip your chainsaw bar at the end of every use, particularly when you are cleaning up. Others suggest a more relaxed approach advising that you flip the chainsaw bar only when you are changing your chainsaw blade.
How much does a Stihl 881 cost?
$2,029.99. The largest and most powerful chainsaw in the STIHL lineup. For the largest, toughest and most demanding jobs, professionals can find the performance they need in the MS 881 chainsaw.
Is it easier to chainsaw wet or dry wood?
No, it is not bad to cut the wet wood with your chainsaw. Dewdrops, raindrops, or the snow on the wood will not cause any harm to your chainsaw. It is, in fact, much easier to cut through the wet wood than dry wood because the extra moisture on the wood will act as a natural lubricant.
What can I use instead of an auger?
A spud bar or digging iron will work fine. I made my spud bars out of rebar and a piece of flat steel that I machined and hardened.
Do you need to break in a chainsaw?
Typically we recommend a break in period of 6-10 tanks of fuel. During this period the engine should not be allowed to run at high RPMs for extended periods of time.
How long should you run a chainsaw?
Depending on the type and usage, you can expect a gas Chainsaw to run between 15 and 40 min before you have to fill it up again. Most battery-powered chainsaws have a run time of up to 2 hours, but there are high-capacity power packs that will last much longer.